Media Over QUIC Y. You Internet-Draft S. Gül Intended status: Informational L. Kondrad Expires: 19 May 2027 P. Rondao Alface L. Ilola Nokia 15 November 2026 Transport of V3C Bitstreams over Media over QUIC Transport (MOQT) draft-yuyou-moq-v3c-01 Abstract This document specifies a mapping and packaging for transporting ISO/ IEC 23090-5 Visual Volumetric Video-based Coding (V3C) bitstreams over Media over QUIC Transport (MOQT). The mapping uses the MOQT Streaming Format (MSF): V3C configuration is MSF initialization data, each independently consumable V3C component is an MSF track, a run of V3C composition units that starts at a random access point is a MOQT Group, and the coded data of one component for one composition unit is a MOQT Object. Relays remain unaware of V3C syntax. V3C knowledge is confined to the streaming-format layer. About This Document This note is to be removed before publishing as an RFC. The latest revision of this draft can be found at https://yuyou.github.io/v3c/. Status information for this document may be found at https://datatracker.ietf.org/doc/draft-yuyou-moq- v3c/. Discussion of this document takes place on the Media Over QUIC Working Group mailing list (mailto:moq@ietf.org), which is archived at https://mailarchive.ietf.org/arch/browse/moq/. Subscribe at https://www.ietf.org/mailman/listinfo/moq/. Source for this draft and an issue tracker can be found at https://github.com/yuyou/v3c. Status of This Memo This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79. You, et al. Expires 19 May 2027 [Page 1] Internet-Draft V3C over MOQT November 2026 Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet- Drafts is at https://datatracker.ietf.org/drafts/current/. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." This Internet-Draft will expire on 19 May 2027. Copyright Notice Copyright (c) 2026 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (https://trustee.ietf.org/ license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Revised BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Revised BSD License. Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 3 2. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 5 3. Relationship to MSF . . . . . . . . . . . . . . . . . . . . . 7 4. Architecture . . . . . . . . . . . . . . . . . . . . . . . . 7 5. Mapping V3C to the MOQT Object Model . . . . . . . . . . . . 10 5.1. Encapsulation Modes . . . . . . . . . . . . . . . . . . . 10 5.2. Tracks . . . . . . . . . . . . . . . . . . . . . . . . . 10 5.2.1. Component Presence . . . . . . . . . . . . . . . . . 12 5.2.2. Map Streams . . . . . . . . . . . . . . . . . . . . . 13 5.2.3. Auxiliary Sub-Bitstreams . . . . . . . . . . . . . . 13 5.2.4. Atlas Tiles . . . . . . . . . . . . . . . . . . . . . 14 5.3. Initialization Data . . . . . . . . . . . . . . . . . . . 14 5.3.1. Contents of the VPS . . . . . . . . . . . . . . . . . 15 5.3.2. Attribute Types in the VPS . . . . . . . . . . . . . 17 5.3.3. Join Sequence . . . . . . . . . . . . . . . . . . . . 18 5.4. Groups and Random Access . . . . . . . . . . . . . . . . 19 5.5. Objects, Subgroups, and Datagrams . . . . . . . . . . . . 21 5.6. Object Payload Format . . . . . . . . . . . . . . . . . . 22 5.6.1. Native Framing . . . . . . . . . . . . . . . . . . . 23 5.6.2. ISOBMFF Framing . . . . . . . . . . . . . . . . . . . 24 You, et al. Expires 19 May 2027 [Page 2] Internet-Draft V3C over MOQT November 2026 5.7. Datagram Delivery Guidelines for V3C . . . . . . . . . . 25 5.7.1. Encoding Considerations for Datagram Delivery . . . . 26 6. V3C Packaging . . . . . . . . . . . . . . . . . . . . . . . . 27 7. Catalog Signaling for V3C . . . . . . . . . . . . . . . . . . 28 7.1. V3C packaging type . . . . . . . . . . . . . . . . . . . 28 7.2. V3C Track Identifiers . . . . . . . . . . . . . . . . . . 28 7.3. Track Roles . . . . . . . . . . . . . . . . . . . . . . . 32 7.4. Dependencies and Render Groups . . . . . . . . . . . . . 33 7.5. Alternate Groups . . . . . . . . . . . . . . . . . . . . 33 7.6. Catalog Examples . . . . . . . . . . . . . . . . . . . . 34 7.6.1. Packed Video Component Mode . . . . . . . . . . . . . 36 7.6.2. Packed Video Component Mode with Native Framing . . . 38 7.6.3. Unpacked Component Mode with Multiple Attributes . . 40 7.6.4. Video-based Dynamic Mesh Coding (V-DMC) . . . . . . . 45 7.6.5. Spatial Subdivision with Atlas Tile Tracks . . . . . 47 8. Prioritization Considerations . . . . . . . . . . . . . . . . 52 9. Relationship to the RTP Payload Format for V3C . . . . . . . 52 10. Security Considerations . . . . . . . . . . . . . . . . . . . 53 11. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 54 12. References . . . . . . . . . . . . . . . . . . . . . . . . . 54 12.1. Normative References . . . . . . . . . . . . . . . . . . 54 12.2. Informative References . . . . . . . . . . . . . . . . . 56 Appendix A. Design Options for Datagram-Mode Encoding . . . . . 57 A.1. Problem . . . . . . . . . . . . . . . . . . . . . . . . . 57 A.2. Option A: Encoder-Constrained Coded Unit (Working Specification) . . . . . . . . . . . . . . . . . . . . . 58 A.3. Option B: NAL Unit or Slice as Datagram Object . . . . . 59 A.4. Option C: Application-Level Fragments of One Coded Unit . . . . . . . . . . . . . . . . . . . . . . . . . . 60 A.5. Option D: RFC 10034 RTP Payload Format for V3C . . . . . 60 A.6. Option E: Datagrams Only for Units That Already Fit . . . 61 A.7. Orthogonal Questions . . . . . . . . . . . . . . . . . . 62 A.8. Requested WG Input to Datagram Design Options . . . . . . 62 Appendix B. Single-Track Encapsulation Mode . . . . . . . . . . 63 B.1. Track and Catalog . . . . . . . . . . . . . . . . . . . . 63 B.2. Initialization Data . . . . . . . . . . . . . . . . . . . 63 B.3. Object Payload . . . . . . . . . . . . . . . . . . . . . 64 Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . . . 64 Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 64 1. Introduction Visual Volumetric Video-based Coding (V3C) as specified in [ISOIEC23090-5] represents volumetric media as multiple synchronized component bitstreams and associated atlas data. A V3C bitstream is a sequence of V3C units. Unit types defined by [ISOIEC23090-5] are the V3C parameter set (VPS), atlas data (AD), occupancy video data (OVD), geometry video data (GVD), attribute video data (AVD), packed video You, et al. Expires 19 May 2027 [Page 3] Internet-Draft V3C over MOQT November 2026 data (PVD), common atlas data (CAD), basemesh data (BMD), and arithmetic-coded displacement data (ADD). [RFC10034], Table 1, summarizes an earlier unit-type list in which types 7 through 31 were reserved; this document follows [ISOIEC23090-5] for the current identifiers (Section 7.2). V3C defines a generic high-level syntax for representing volumetric media as a collection of synchronized component bitstreams, together with signaling for their identification, configuration, and reconstruction. [ISOIEC23090-5], Clause 6.3, defines application extensions that plug into that syntax: Video-based Point Cloud Compression (V-PCC) in Annex H of [ISOIEC23090-5], MPEG Immersive Video (MIV) in [ISOIEC23090-12], and Video-based Dynamic Mesh Coding (V-DMC) in [ISOIEC23090-29]. This document maps the generic V3C unit stream to the MOQT data model. It does not specify V-PCC reconstruction, MIV camera or common-atlas payload syntax, or V-DMC mesh decoding. Atlas and VPS extensions (asps_vpcc_extension, asps_miv_extension, asps_vdmc_extension, vps_extension) remain inside VPS and atlas payloads. Media over QUIC Transport (MOQT) [I-D.ietf-moq-transport-23] provides publish/subscribe-based delivery over QUIC [RFC9000] and WebTransport. The MOQT Streaming Format (MSF) [I-D.ietf-moq-msf] defines a catalog, initialization data, time-aligned groups, and track selection on top of MOQT. MSF defines Low Overhead Container (LOC) [I-D.ietf-moq-loc] packaging for audio and video ([I-D.ietf-moq-msf], Section 4.1), in which each encoded audio or video sample is one MOQT Object and the samples of a group of pictures are placed in one MOQT Group. The LOC sample model is insufficient for V3C. Atlas data does not have the semantics of an encoded video sample represented by the WebCodecs EncodedVideoChunk interface [W3C-WEBCODECS]. Instead, it carries reconstruction metadata, including patch placement and the mapping between 3D geometry and the 2D component videos. Occupancy, geometry, attribute, packed, basemesh, and displacement bitstreams, when present, are distinct V3C components. Carrying those components on separate tracks allows a receiver to obtain them with SUBSCRIBE or FETCH and to prioritize or omit them independently. Such selection remains subject to the component presence and dependencies signaled by the active VPS and the catalog; a receiver that omits a required component cannot reconstruct the corresponding volumetric frame. The VPS is sequence-level decoder configuration, not temporal media. Consistent with that role, [RFC10034] signals the VPS out of band using sprop-v3c-parameter-set, rather than carrying it as a media packet stream. You, et al. Expires 19 May 2027 [Page 4] Internet-Draft V3C over MOQT November 2026 This document therefore defines a V3C packaging value for MSF, analogous to the way [I-D.ietf-moq-cmsf] adds CMAF packaging on top of MSF. It operates at the streaming-format layer and does not modify MOQT. [ISOIEC23090-5] specifies the V3C bitstream, VPS, and unit types. [ISOIEC23090-10] specifies carriage of V3C data in the ISO Base Media File Format and Dynamic Adaptive Streaming over HTTP (DASH). [RFC10034] specifies carriage of V3C atlas data over RTP. This document specifies carriage of the same V3C components over MOQT and their description in the MSF catalog. This document is written against draft-ietf-moq-transport-23 and thus uses MOQT version 23 terminology, including Delivery Mode, Track Properties and Object Properties, SUBSCRIBE_TRACKS, REQUEST_UPDATE, PUBLISH_DONE, and the data-plane distinction between Subgroup stream delivery and Datagram delivery. [I-D.ietf-moq-msf] is written against an earlier MOQT version and requires a Joining FETCH to obtain the catalog; draft-ietf-moq-transport-23 replaces Joining FETCH with fill fetch streams requested using FILL_PARAMETERS. This document uses the MOQT version 23 mechanism (Section 5.3.3). This document does not redefine V3C bitstream syntax or semantics, and it does not specify a video or mesh codec for V3C components. When Datagram delivery is used, Section 5.7.1 requires the complete MOQT Object to fit within the datagram size limit of the underlying QUIC or WebTransport session. To satisfy this requirement, an encoder can limit the sizes of slices and NAL units. Appendix A compares alternative approaches and lists questions for Working Group consideration. 2. Terminology The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all capitals, as shown here. This document uses the following terms: V3C component: Atlas, occupancy, geometry, or attribute data of a particular type associated with a V3C volumetric content representation, as defined in [ISOIEC23090-5] and restated in [RFC10034]. Packed video data, common atlas data, basemesh data, and arithmetic-coded displacement data, when present, are also treated as V3C components in this mapping. V3C parameter set (VPS): A syntax structure containing syntax You, et al. Expires 19 May 2027 [Page 5] Internet-Draft V3C over MOQT November 2026 elements that apply to zero or more coded V3C sequences, as defined in [ISOIEC23090-5]. The VPS is configuration, not a temporal media component. Among other decoder resources, it maps each attribute index to an attribute type (Section 5.3.2) and indicates which component sub-bitstreams are present (Section 5.2.1). Attribute: A scalar or vector property optionally associated with each point in a volumetric frame, such as color, reflectance, surface normal, transparency, or material ID ([ISOIEC23090-5]). V3C unit: A V3C unit header and payload as defined in [ISOIEC23090-5]. The header identifies the unit type and, when present, atlas, map, packed-map, attribute, auxiliary-video, and related indices ([RFC10034], Section 4.3.1; Section 7.2). Coded V3C unit: The coded data of one V3C component for one V3C composition unit, typically one coded atlas access unit or one coded video access unit. Network Abstraction Layer (NAL) units, when used by the underlying codec, are contained in this payload; they are not the MOQT Object boundary. V3C composition unit: The set of all sub-bitstream composition units that share the same composition time, as defined in [ISOIEC23090-5]. One composition unit reconstructs one coded volumetric frame. IRAP composition unit: A V3C composition unit in which every carried component starts with an intra random access point (IRAP), as defined in [ISOIEC23090-5]. MOQT Track, Group, Subgroup, and Object: The hierarchical data model elements defined by [I-D.ietf-moq-transport-23] for naming, ordering, and transporting media objects. Delivery Mode: An enumeration associated with a MOQT object that indicates whether the object is sent on a subgroup stream (Subgroup) or as a single object datagram (Datagram). The Original Publisher establishes an object's Delivery Mode by how it first transmits the object. The Delivery Mode is a property of an individual object and can vary among objects in the same track. In a subscription, an object is sent according to its Delivery Mode ([I-D.ietf-moq-transport-23], Sections 2.1 and 2.1.1). MSF Catalog: The MSF catalog track defined in [I-D.ietf-moq-msf], which advertises tracks, relationships, selection properties, and initialization data. You, et al. Expires 19 May 2027 [Page 6] Internet-Draft V3C over MOQT November 2026 3. Relationship to MSF All requirements and terminology in [I-D.ietf-moq-msf] apply unless this document states otherwise. This specification adds: * the catalog packaging value v3c (Section 7.1); * rules for carrying the VPS and component decoder configuration in the catalog Initialization Data List (Section 5.3); * recovery of attribute type from that VPS (Section 5.3.2); * a track-level v3c object that copies identifiers from the V3C unit header (Section 7.2); * two Object payload framings: native framing using only [ISOIEC23090-5] syntax, and ISOBMFF framing using the sample formats of [ISOIEC23090-10] (Section 5.6); * a mapping from V3C components, composition units, and coded units onto MSF tracks, MOQT Groups, and MOQT Objects (Section 5). A V3C component track MUST NOT use the MSF packaging value loc. LOC packaging remains available for ordinary audio and video tracks in the same catalog, for example an accompanying 2D video or audio commentary track. 4. Architecture V3C syntax stays at the streaming-format layer. MOQT carries opaque objects. Relays forward using MOQT Track, Group, Subgroup, Object, priority, and timeout metadata only. Figure 1 shows the layering. Table 1 summarizes the mapping. You, et al. Expires 19 May 2027 [Page 7] Internet-Draft V3C over MOQT November 2026 V3C content | +--------------+---------------+ | | V3C configuration V3C media | | VPS independently consumable | components present in the VPS | | | AD CAD OVD GVD | AVD PVD BMD ADD | +------------------+------------------+ | MSF packaging | +--------------+--------------+ | | | Track A Track B Track C | | | Groups Groups Groups | | | Objects Objects Objects | | | +--------------+--------------+ | MOQT | QUIC Figure 1: V3C packaging relative to MSF and MOQT The mapping is: You, et al. Expires 19 May 2027 [Page 8] Internet-Draft V3C over MOQT November 2026 +======================+============================================+ | V3C | MSF / MOQT | +======================+============================================+ | VPS | initDataList entry referenced by the atlas | | | track initRef: v3c_parameter_set() (native | | | framing) or V3CDecoderConfigurationRecord | | | (ISOBMFF framing) | +----------------------+--------------------------------------------+ | Component decoder | In band (native framing), or initDataList | | configuration | entry referenced by the component track | | | initRef (ISOBMFF framing) | +----------------------+--------------------------------------------+ | Each independently | One MSF track | | consumable | | | component (AD, OVD, | | | GVD, AVD, PVD, CAD, | | | BMD, ADD) | | +----------------------+--------------------------------------------+ | Run of V3C | One MOQT Group, with identical Group IDs | | composition units | across time-aligned tracks | | starting at an IRAP | | | composition unit | | +----------------------+--------------------------------------------+ | Coded V3C unit (one | One MOQT Object | | component, one | | | composition unit) | | +----------------------+--------------------------------------------+ | NAL unit | Bytes inside the object payload | +----------------------+--------------------------------------------+ | Component identity | Catalog v3c object | | (vuh_*) | | +----------------------+--------------------------------------------+ | Decode dependency | Catalog depends | +----------------------+--------------------------------------------+ | Same presentation | Catalog renderGroup | +----------------------+--------------------------------------------+ | Alternate quality | Catalog altGroup | | of one component, | | | including V-DMC GVD | | | and ADD | | | displacement | | +----------------------+--------------------------------------------+ Table 1: V3C to MSF/MOQT mapping You, et al. Expires 19 May 2027 [Page 9] Internet-Draft V3C over MOQT November 2026 5. Mapping V3C to the MOQT Object Model 5.1. Encapsulation Modes An encapsulation mode determines how V3C components are assigned to MOQT tracks. The body of this document specifies multi-track mode. Single-track mode, in which all V3C components share one track, is NOT RECOMMENDED and is specified in Appendix B. Independently of the encapsulation mode, a payload framing determines the byte format of an Object payload (Section 5.6). Multi-track mode: Each independently consumable V3C component is carried on its own MOQT track. This mode enables selective subscription, independent publisher and subscriber priority, and independent congestion response per component. Alternate encodings of the same component are separate tracks that share an altGroup (Section 7.5). In either encapsulation mode, subscribers MUST have catalog metadata sufficient to identify required dependencies (for example atlas data required to interpret geometry or packed video) before decoding. Either encapsulation mode MAY mix Delivery Mode Subgroup and Datagram within a track or group, subject to Section 5.5 and Section 5.7. | Editor's note: Datagram delivery may not be recommended and may | be removed from the scope of the next revision of this | document. 5.2. Tracks In multi-track mode, the publisher exposes a separate track for each V3C component that it offers, and the active VPS (including any VPS packed-video extension) indicates that the component is present (Section 5.2.1). The offered set MAY include: * atlas data (V3C_AD); * atlas tile data (role v3c-atlas-tile), when an atlas frame is partitioned into spatial tiles (Section 5.2.4); * occupancy video data (V3C_OVD), when present; * geometry video data (V3C_GVD), when present; You, et al. Expires 19 May 2027 [Page 10] Internet-Draft V3C over MOQT November 2026 * one track per attribute (V3C_AVD) that the publisher offers independently. The attribute type (for example "texture" or "surface normal") is not encoded in the track name but included in the VPS (Section 5.3.2); * packed video data (V3C_PVD), when present; * common atlas data (V3C_CAD), when present; * basemesh data (V3C_BMD), when present; * arithmetic-coded displacement data (V3C_ADD), when present. Occupancy video, geometry video, attribute video, packed video, common atlas, basemesh, and displacement are optional at the V3C layer. A presentation MUST NOT be assumed to contain atlas, occupancy, geometry, and attribute video tracks together. Packed video MAY be the only video component. In Video-based Dynamic Mesh Coding (V-DMC) [ISOIEC23090-29], basemesh data carries the base mesh. Displacement vectors are carried either as geometry video data (V3C_GVD) or as arithmetic-coded displacement data (V3C_ADD). For a given atlas, those two forms are mutually exclusive in the VPS. A geometry track in that case carries video- coded displacement; it does not replace the basemesh track. Selection between the two forms is specified in Section 7.5. The VPS is not advertised as a continuously running media track (Section 5.3). MOQT Track Names are opaque byte sequences ([I-D.ietf-moq-transport-23]). This specification defines the following recommended UTF-8 naming patterns to make catalog entries readable. The slash (/, byte 0x2f) is an ordinary Track Name byte; it does not create MOQT namespace fields or otherwise have protocol semantics. The Track Namespace remains separately encoded. When a name is rendered using the safe serialization defined in Section 8.8 of [I-D.ietf-moq-transport-23], each slash is encoded as .2f; for example, v3c/attribute/0/0/0 is rendered as v3c.2fattribute.2f0.2f0.2f0. The hyphen is also not rendered verbatim; v3c/common-atlas is rendered as v3c.2fcommon.2datlas. The angle-bracketed identifiers in these patterns are replaced by their non-negative decimal values: You, et al. Expires 19 May 2027 [Page 11] Internet-Draft V3C over MOQT November 2026 v3c/atlas/ v3c/atlas//tile/ v3c/occupancy/ v3c/geometry/ v3c/geometry// v3c/geometry///aux v3c/attribute/// v3c/attribute//// v3c/attribute/////aux v3c/packed/ v3c/packed// v3c/basemesh/ v3c/displacement/ v3c/common-atlas Figure 2: Recommended V3C track name patterns These names are a convention, not the source of component identity. A receiver MUST use the fields in the catalog v3c object (Section 7.2) and MUST NOT require a publisher to use these recommended names. Occupancy, atlas, basemesh, and displacement unit headers do not include vuh_map_index; those tracks omit the map-index path element. Common atlas data has no vuh_atlas_id. Packed-video unit headers carry vuh_packed_map_index rather than vuh_map_index (Section 7.2). Geometry and attribute map splitting is specified in Section 5.2.2. Subscribers obtain V3C component tracks using MOQT subscription procedures. A subscriber MAY send SUBSCRIBE for an individual component track, or SUBSCRIBE_TRACKS to request publication of tracks in a namespace that match advertised catalog metadata and filters. A subscriber MAY later send REQUEST_UPDATE to pause or resume forwarding, or to change filters or subscriber priority ([I-D.ietf-moq-transport-23], Section 9.5). A publisher or relay terminates an established subscription by sending PUBLISH_DONE. 5.2.1. Component Presence A publisher MUST advertise a V3C component track only when the corresponding sub-bitstream is present according to the active VPS and, for packed video, the VPS packed-video extension (vps_packed_video_present_flag). Presence is recovered from the VPS the same way attribute type is recovered (Section 5.3.2). This document does not duplicate VPS presence flags or profile, tier, and level (PTL) fields such as ptl_max_decodes_idc in the catalog. Per atlas, [ISOIEC23090-5] signals: You, et al. Expires 19 May 2027 [Page 12] Internet-Draft V3C over MOQT November 2026 * vps_occupancy_video_present_flag * vps_geometry_video_present_flag * vps_attribute_video_present_flag * vps_auxiliary_video_present_flag * vps_packed_video_present_flag (in a VPS packed-video extension) When packed video is the only video component, occupancy, geometry, and attribute video tracks are omitted. Packed tracks still list the corresponding atlas track in depends (Section 7.4). 5.2.2. Map Streams vps_multiple_map_streams_present_flag in the VPS controls whether maps of a geometry or attribute component occupy one video stream or several ([ISOIEC23090-5]): * When the flag is 0, all maps of that component for an atlas are in one video stream. The publisher advertises one MOQT track for that component and omits v3c.mapIndex (the map index is derived as in [ISOIEC23090-5]). * When the flag is 1, each map is its own stream. The publisher advertises one MOQT track per mapIndex. Multiple maps are a generic VPS feature. Extra maps are used heavily by some V3C applications; the track rule above is not application- specific. 5.2.3. Auxiliary Sub-Bitstreams When vps_auxiliary_video_present_flag is 1, a geometry or attribute component MAY include a distinct auxiliary video sub-bitstream, identified by vuh_auxiliary_video_flag equal to 1 in the V3C unit header. That sub-bitstream is a separate independently consumable component: the publisher advertises a separate MOQT track and sets v3c.auxiliaryVideo to 1 (Section 7.2). Two geometry (or attribute) tracks that share atlas and map identifiers are distinguished by this field. A separate auxiliary track MUST NOT be advertised when the flag is 0. You, et al. Expires 19 May 2027 [Page 13] Internet-Draft V3C over MOQT November 2026 5.2.4. Atlas Tiles [ISOIEC23090-5], Clause 7.4, permits an atlas frame to be partitioned into non-overlapping rectangular tiles. One atlas coding layer (ACL) NAL unit carries one tile. Tiles MAY align with video slices or subpictures. [RFC10034] signals a tile subset with sprop-v3c-tile- id. [ISOIEC23090-10] defines optional atlas tile tracks. The default mapping in this document is that all tiles of an atlas stay in one atlas track. One coded atlas access unit is one MOQT Object. A publisher MAY expose atlas tile tracks. An atlas tile track carries only the ACL NAL units of its tile; the atlas parameter sets and the VPS remain in the atlas track ([ISOIEC23090-10], Clause 7.3.2.2). An atlas tile track includes v3c.tileId, lists the atlas track in depends, and references the same initDataList entry as the atlas track. Video, basemesh, or displacement tracks that are spatially aligned with that tile SHOULD also list the tile track in depends. Per-tile tracks are not required. This document does not require viewport-driven delivery. 5.3. Initialization Data The VPS MUST be provided as MSF initialization data, not as a continuously running media track. This matches the out-of-band VPS treatment in [RFC10034] (sprop-v3c-parameter-set). Each initialization data item is carried in the catalog initDataList ([I-D.ietf-moq-msf], Section 5.1.7) as an entry with type equal to inline, whose data value is the Base64 encoding [RFC4648] of the item. The items depend on the payload framing of the track (Section 5.6). With native framing, the atlas track references with initRef ([I-D.ietf-moq-msf], Section 5.2.13) an entry that contains the v3c_parameter_set() syntax structure of the active VPS, without a V3C unit header. This is the same value as sprop-v3c-parameter-set in [RFC10034]. Atlas parameter sets, SEI messages, and the parameter sets of the video, basemesh, and displacement sub-bitstreams are carried in band in the Objects (Section 5.3.1). Video, basemesh, and displacement tracks that use native framing do not have an initRef. With ISOBMFF framing, each V3C-packaged track references one decoder configuration record with initRef. The record is the structure that [ISOIEC23090-10] or [ISOIEC14496-15] places in the corresponding ISOBMFF sample entry, without the enclosing box header: You, et al. Expires 19 May 2027 [Page 14] Internet-Draft V3C over MOQT November 2026 +===================+==========================================+ | Track | Decoder configuration record | +===================+==========================================+ | Atlas (V3C_AD), | V3CDecoderConfigurationRecord with | | common atlas | version 1 ([ISOIEC23090-10], Clause | | (V3C_CAD) | 6.2.1) | +-------------------+------------------------------------------+ | Atlas tile | The record of the atlas track that the | | | tile track depends on | +-------------------+------------------------------------------+ | Video (V3C_OVD, | Decoder configuration record of the | | V3C_GVD, V3C_AVD, | video codec, for example | | V3C_PVD) | HEVCDecoderConfigurationRecord | | | ([ISOIEC14496-15]) | +-------------------+------------------------------------------+ | Basemesh | BaseMeshDecoderConfigurationRecord | | (V3C_BMD) | ([ISOIEC23090-10], Clause 6.2.2) | +-------------------+------------------------------------------+ | Displacement | ACDisplacementDecoderConfigurationRecord | | (V3C_ADD) | ([ISOIEC23090-10], Clause 6.2.3) | +-------------------+------------------------------------------+ Table 2: Decoder configuration record referenced by initRef The V3CDecoderConfigurationRecord of the atlas track carries the active VPS as a complete V3C unit of type V3C_VPS, including its V3C unit header ([ISOIEC23090-10], Clause 6.2.1). This differs from sprop-v3c-parameter-set in [RFC10034], which carries only the v3c_parameter_set() syntax structure. The record MAY also carry atlas parameter sets and SEI messages in its setup unit arrays. Other V3C component tracks do not reference the VPS directly. Each such track lists the atlas track in depends (Section 7.4), and a receiver obtains the VPS from the initialization data of that atlas track. The id of each initDataList entry MUST be unique within the catalog. Tracks that use identical decoder configuration MAY reference the same entry. 5.3.1. Contents of the VPS This subsection restates the role of the VPS for the MOQT mapping. It does not redefine VPS syntax. Syntax and semantics remain as specified in [ISOIEC23090-5] and as summarized in [RFC10034], Section 4.2. You, et al. Expires 19 May 2027 [Page 15] Internet-Draft V3C over MOQT November 2026 The VPS is carried in a V3C unit of type V3C_VPS. It applies to zero or more coded V3C sequences. Media-component unit headers identify the active VPS with vuh_v3c_parameter_set_id, which equals vps_v3c_parameter_set_id of that VPS ([RFC10034], Section 4.3.1). Catalog v3c.parameterSetId, when present, copies the same identifier. One VPS governs the components of the coded V3C sequence (CVS) it applies to. Atlas data (V3C_AD), geometry video data (V3C_GVD), attribute video data (V3C_AVD), occupancy video data (V3C_OVD), and packed video data (V3C_PVD) do not use a separate parameter set for each media type. Every such unit carries vuh_v3c_parameter_set_id and thereby refers to that same active VPS. The catalog records that VPS once, in the initialization data of the atlas track (Section 5.3). The VPS is sequence-level configuration for the CVS, not a per- component parameter set. It includes the atlas geometry configuration in geometry_information() (codec identifiers and the 2D and 3D bit depths), and attribute configuration in attribute_information(). attribute_information() maps each attribute index to an attribute type, such as texture or, for a Gaussian splatting representation, spherical harmonics, scale, rotation, or opacity (Section 5.3.2). This document does not specify Gaussian reconstruction. A receiver uses the VPS to determine the resources required to decode and reconstruct the bitstream: which atlas, occupancy, geometry, attribute, packed, auxiliary, basemesh, and displacement components are present, how they relate, and which attribute type each AVD component carries (Section 5.3.2). Placing the VPS in catalog initialization data is the MOQT counterpart of carrying it out of band in SDP as sprop-v3c-parameter-set ([RFC10034]). VPS extensions (packed video, MIV, V-DMC) travel inside the VPS bytes. This document does not parse those extensions in the catalog. Profile, tier, and level, including ptl_max_decodes_idc, are recovered from the VPS; they are not duplicated as catalog fields. With native framing, atlas sequence parameter sets (ASPS), atlas frame parameter sets (AFPS), and Supplemental Enhancement Information (SEI) messages are carried in the atlas Objects. Because every Group starts with an IRAP composition unit (Section 5.4), the first Object of each Group of a track that uses native framing MUST contain the parameter sets needed to decode that track from that Object. With ISOBMFF framing, ASPS, AFPS, and SEI messages MAY be carried in the setup unit arrays of the V3CDecoderConfigurationRecord, in the atlas Objects, or in both, subject to the array_completeness values You, et al. Expires 19 May 2027 [Page 16] Internet-Draft V3C over MOQT November 2026 of the record ([ISOIEC23090-10], Clause 6.2.1). A publisher that does not mark those arrays complete SHOULD repeat the parameter sets in the first atlas Object of each Group. Video-codec configuration for OVD, GVD, AVD, or PVD (for example HEVC or VVC parameter sets) is not part of the VPS. With native framing, it is carried in band in the video sub-bitstream. With ISOBMFF framing, it is carried in the decoder configuration record that the video track references with initRef. Basemesh and displacement configuration is likewise carried in band with native framing, or in the records listed in Table 2 with ISOBMFF framing; payload syntax for those components is specified in [ISOIEC23090-29]. 5.3.2. Attribute Types in the VPS An attribute is a property of reconstructed volumetric primitives. Examples include texture (color), material ID, transparency, reflectance, surface normal, spherical harmonics, scale, and rotation ([ISOIEC23090-5], Table 5). The catalog identifies an AVD track by v3c.attributeIndex, which copies vuh_attribute_index from the V3C unit header. That index is not itself the attribute type. The VPS maps each vuh_attribute_index to the type of attribute carried by the corresponding AVD component. A V3C decoder uses that mapping to identify which attribute a given video component contains, for example color ([RFC10034], Section 4.3.1). VPS (atlas track initRef) | | attribute_index 0 -> texture (color) | attribute_index 1 -> surface normal v AVD tracks v3c/attribute/0/0/0 v3c.attributeIndex = 0 v3c/attribute/0/1/0 v3c.attributeIndex = 1 Figure 3: Attribute type is recovered from the VPS In the recommended track name v3c/ attribute///, the three numbers identify: * atlasId: the atlas to which the attribute belongs; * attributeIndex: the zero-based attribute entry in that atlas's VPS attribute information; and You, et al. Expires 19 May 2027 [Page 17] Internet-Draft V3C over MOQT November 2026 * attributePartitionIndex: the zero-based partition of that attribute. Thus, v3c/attribute/0/0/0 means atlas 0, attribute 0, partition 0. The VPS says what attribute 0 represents, such as texture (color). Likewise, v3c/attribute/0/1/0 means atlas 0, attribute 1, partition 0. If attribute 0 were split into two partitions, their recommended names would end in /0/0 and /0/1. These names are a readable convention; receivers use the corresponding fields in the catalog v3c object rather than parsing the track name. A subscriber that needs a particular attribute type (for example color, and not surface normals) parses the referenced VPS and subscribes to the AVD track or tracks whose attributeIndex maps to that type. This document does not duplicate attribute-type names in the catalog. The VPS is authoritative. An attribute MAY be partitioned across several AVD components when, for example, the attribute has more dimensions than the video codec can code in one stream ([RFC10034], Section 7.3). The VPS describes that partitioning. Catalog v3c.attributePartitionIndex identifies which partition a track carries. 5.3.3. Join Sequence Joining a V3C presentation uses the catalog, then initialization data, then media, as shown in Figure 4. Fill fetch streams are requested with FILL_PARAMETERS ([I-D.ietf-moq-transport-23], Section 3.4): You, et al. Expires 19 May 2027 [Page 18] Internet-Draft V3C over MOQT November 2026 Subscriber | | SUBSCRIBE catalog (FILL_PARAMETERS to Largest Object) v Catalog | | atlas initRef -> VPS | other initRef -> component decoder configuration | (ISOBMFF framing only) v V3C initialization | | SUBSCRIBE component tracks at the latest Group | (Location Filter + FILL_PARAMETERS) v Time-aligned Groups | v Decode Figure 4: Join sequence for a V3C presentation A subscriber MUST NOT begin decoding V3C component tracks until it has obtained the VPS and, for tracks that use ISOBMFF framing, the decoder configuration record of each subscribed track. In multi-track mode, the VPS is carried only in initialization data; Appendix B specifies an exception for single-track mode. If the active VPS changes, the publisher MUST publish a catalog update with a new initDataList entry and updated initRef values. 5.4. Groups and Random Access One MOQT Group carries a run of one or more consecutive V3C composition units that begins with an IRAP composition unit. Each Group is therefore a join point at which a subscriber can start decoding, consistent with the MOQT requirement that Groups be independently useful ([I-D.ietf-moq-transport-23], Section 2.3) and with the MSF requirement that a group of pictures be placed within one MOQT Group ([I-D.ietf-moq-msf], Section 4.1). Within a Group, each Object carries the coded V3C unit of one composition unit, in decoding order (Section 5.5). You, et al. Expires 19 May 2027 [Page 19] Internet-Draft V3C over MOQT November 2026 Component tracks that belong to the same renderGroup and that reconstruct the same volumetric frames MUST use identical MOQT Group IDs and identical Object IDs for corresponding composition units. This requirement is stricter than the time-alignment guidance in [I-D.ietf-moq-msf], Section 4.2, and allows a receiver to associate the coded V3C units of one composition unit without parsing the payloads. Every Group MUST begin with an IRAP composition unit: the first Object of every carried component is a random access point. For atlas and common-atlas data, that is an IRAP coded atlas access unit (an atlas access unit whose ACL NAL units have a NAL_IDR_W_RADL, or NAL_IDR_N_LP, NAL_GIDR_W_RADL, NAL_GBLA_N_LP, NAL_GCRA or NAL_GIDR_N_LP NAL unit type as specified in [ISOIEC23090-5]). For video-coded components, it is the IRAP defined by the video codec in use, for example an Instantaneous Decoding Refresh (IDR) or Clean Random Access (CRA) picture. For a non-video component, it is the random access point defined by that component's coding specification. A coded V3C sequence (CVS) starts with a VPS, which can be provided out of band, and its first composition unit is an IRAP composition unit ([ISOIEC23090-5]). A coded V3C unit MUST NOT span Groups. Example of cross-track alignment, with two Groups of two composition units each: Group 100 (starts with an IRAP composition unit) v3c/atlas/0 Object 0: AD[0] Object 1: AD[1] v3c/occupancy/0 Object 0: OVD[0] Object 1: OVD[1] v3c/geometry/0 Object 0: GVD[0] Object 1: GVD[1] v3c/attribute/0/0/0 Object 0: AVD[0] Object 1: AVD[1] Group 101 (starts with an IRAP composition unit) v3c/atlas/0 Object 0: AD[2] Object 1: AD[3] v3c/occupancy/0 Object 0: OVD[2] Object 1: OVD[3] v3c/geometry/0 Object 0: GVD[2] Object 1: GVD[3] v3c/attribute/0/0/0 Object 0: AVD[2] Object 1: AVD[3] Figure 5: Equal Group and Object IDs align V3C components in time You, et al. Expires 19 May 2027 [Page 20] Internet-Draft V3C over MOQT November 2026 5.5. Objects, Subgroups, and Datagrams A MOQT Object carries one coded V3C unit: the coded data of the track's component for one V3C composition unit. Object IDs within a Group follow the decoding order of the composition units. For a video-coded component, the Object is one coded video access unit. For atlas or common-atlas data, it is one coded atlas access unit, which contains zero or more atlas NAL units. For basemesh or displacement data, it is one coded access unit of that component. NAL units are an underlying codec structure. They remain inside the object payload. Publishers SHOULD NOT place each NAL unit in its own MOQT Object solely to express codec framing. When datagram delivery is used, slice and NAL unit size is constrained at encode time (Section 5.7.1). In multi-track mode, the four-byte V3C unit header is not carried in the object. Header fields needed to identify the component are advertised in the catalog v3c object (Section 7.2). The payload format is specified in Section 5.6. MOQT defines a Delivery Mode for each object ([I-D.ietf-moq-transport-23], Section 2.1.1). The Delivery Mode can be Subgroup or Datagram, and it can vary among objects in the same track. The Original Publisher establishes the Delivery Mode by how it first transmits the object, and in a subscription an object MUST be sent according to its Delivery Mode. When an object has Delivery Mode Subgroup, it is delivered on a MOQT subgroup stream. Subgroups provide ordered delivery on a single QUIC stream. They MAY distinguish independently discardable layers of the same component, for example a base layer and an enhancement layer of geometry: Track: v3c/geometry/0/0 Group 100 Subgroup 0 (base) Object 0 Object 1 Subgroup 1 (enhancement) Object 0 Object 1 Figure 6: Subgroups as layers of one V3C component When no such layering is offered, a publisher MAY place every object of the Group on subgroup 0. You, et al. Expires 19 May 2027 [Page 21] Internet-Draft V3C over MOQT November 2026 In multi-track mode, subgroups MUST NOT be used as the primary means of separating V3C component types; those are separate tracks (Section 5.2). When an object has Delivery Mode Datagram, it is conveyed as a single MOQT object datagram. Such an object is not sent in a subgroup and has no Subgroup ID. Datagram delivery is suitable for V3C coded units where low latency is preferred over reliable delivery, especially when the unit is independently useful, replaceable by newer data, or can be skipped without preventing future decoding or rendering. A sender using datagram delivery MUST ensure that the complete MOQT object header, any object properties, and the object payload fit within the maximum datagram size for the session. If the total object size exceeds the maximum datagram size, the object will be dropped without explicit notification ([I-D.ietf-moq-transport-23], Section 11.2). That session maximum is bounded by the underlying QUIC or WebTransport datagram limit (Section 5.7.1). Application- level fragmentation of one coded V3C unit across multiple MOQT datagrams is unspecified. For V3C units that may exceed the datagram size, or for data that requires reliable in-order delivery, the publisher MUST use subgroup stream delivery instead of datagram delivery. The RTP payload format for V3C [RFC10034] defines packetization of one or more V3C atlas NAL units and fragmentation of a V3C atlas NAL unit across RTP packets. This document does not define RTP packetization inside MOQT objects and does not define a V3C datagram fragment header. 5.6. Object Payload Format [ISOIEC23090-5] specifies the V3C unit stream and the NAL unit stream, and leaves the framing of those units to the application ([ISOIEC23090-5], Clauses 7.2 and 7.3). This document defines two payload framings: Native framing: The Object payload consists only of syntax structures specified in [ISOIEC23090-5] and [ISOIEC23090-29] (Section 5.6.1). No ISOBMFF structure is used. ISOBMFF framing: The Object payload is identical to the corresponding ISOBMFF sample specified in [ISOIEC23090-10] (Section 5.6.2). This allows conversion between MOQT Objects and ISOBMFF samples without rewriting payload bytes. You, et al. Expires 19 May 2027 [Page 22] Internet-Draft V3C over MOQT November 2026 The framing of a track is signaled by v3c.framing (Section 7.2). Native framing is the default. All V3C tracks in the same renderGroup MUST use the same framing. | Editor's note: The name, values, and default of v3c.framing are | proposals for discussion. 5.6.1. Native Framing In multi-track mode, an Object payload is the V3C unit payload of one V3C unit, without its four-byte V3C unit header ([ISOIEC23090-5], Clause 8.3.2.3): +===========+=======================================================+ | Component | Object payload | +===========+=======================================================+ | AD, CAD | atlas_sub_bitstream() ([ISOIEC23090-5], | | | Clause 8.3.2.4): a | | | sample_stream_nal_header() followed by | | | sample_stream_nal_unit() structures | | | ([ISOIEC23090-5], Annex D) | +-----------+-------------------------------------------------------+ | AD (atlas | As for the atlas track, containing only | | tile | the ACL NAL units of the carried tiles | | track) | (Section 5.2.4) | +-----------+-------------------------------------------------------+ | OVD, GVD, | video_sub_bitstream(): a video unit stream | | AVD, PVD | in which unit boundaries are identifiable | | | from patterns in the data, in the format | | | identified by PtlVideoCodecGroupIdc or by | | | a component codec mapping SEI message | | | ([ISOIEC23090-5], Clause 8.4.2.3) | +-----------+-------------------------------------------------------+ | BMD | basemesh_sub_bitstream() in the NAL sample | | | stream format identified by 4CC bmsf | | | ([ISOIEC23090-29]) | +-----------+-------------------------------------------------------+ | ADD | displacement_sub_bitstream() in the NAL | | | sample stream format identified by 4CC | | | dacf ([ISOIEC23090-29]) | +-----------+-------------------------------------------------------+ Table 3: Object payload with native framing You, et al. Expires 19 May 2027 [Page 23] Internet-Draft V3C over MOQT November 2026 An atlas, common-atlas, or atlas tile Object payload begins with its own sample_stream_nal_header(), so the size of each ssnu_nal_unit_size field is known without initialization data. A video Object payload uses the framing of the video unit stream, for example the byte stream format of the video codec with start codes. 5.6.2. ISOBMFF Framing With ISOBMFF framing, an Object payload in multi-track mode is identical to the corresponding ISOBMFF sample of [ISOIEC23090-10]. The size of the length field is taken from the decoder configuration record that the track references with initRef (Section 5.3). +=========+====================+========================================+ |Component|Object payload |Length field size from | +=========+====================+========================================+ |AD, CAD |V3CAtlasSample |unit_size_precision_bytes_minus1 of | | |([ISOIEC23090-10], |V3CDecoderConfigurationRecord | | |Clause 7.3.2.3) | | +---------+--------------------+----------------------------------------+ |AD (atlas|V3CAtlasSample, |as for the atlas track (Section 5.2.4) | |tile |containing only the | | |track) |ACL NAL units of the| | | |carried tiles | | +---------+--------------------+----------------------------------------+ |OVD, GVD,|Length-prefixed |Decoder configuration record of the | |AVD, PVD |video sample as |video codec, for example | | |specified for the |lengthSizeMinusOne of | | |video codec in |HEVCDecoderConfigurationRecord | | |[ISOIEC14496-15] | | +---------+--------------------+----------------------------------------+ |BMD |BaseMeshSample |unit_size_precision_bytes_minus1 of | | |([ISOIEC23090-10], |BaseMeshDecoderConfigurationRecord | | |Clause 7.6.3) | | +---------+--------------------+----------------------------------------+ |ADD |ACDisplacementSample|unit_size_precision_bytes_minus1 of | | |([ISOIEC23090-10], |ACDisplacementDecoderConfigurationRecord| | |Clause 7.6.3) | | +---------+--------------------+----------------------------------------+ Table 4: Object payload with ISOBMFF framing An atlas Object MAY have a zero-length payload; as in [ISOIEC23090-10], such an Object documents the timing of a composition unit for which no atlas NAL unit is present. Video, basemesh, and displacement payloads do not use start codes. You, et al. Expires 19 May 2027 [Page 24] Internet-Draft V3C over MOQT November 2026 5.7. Datagram Delivery Guidelines for V3C MOQT datagrams provide low-latency unreliable delivery of individual objects. A V3C publisher SHOULD consider datagram delivery for: * coded V3C units that fit within the negotiated datagram size and that remain useful under loss; * viewport-driven tile, level-of-detail, or enhancement data that can be skipped under loss; * late or time-sensitive updates where retransmission would no longer be useful; * optional attribute or auxiliary data where omission degrades quality but does not prevent continued rendering. A V3C publisher SHOULD prefer subgroup stream delivery for: * random-access information required at group boundaries; * coded video access units or other payloads likely to exceed the datagram size; * any object for which reliable delivery and ordered processing are required by the application. For datagram-delivered V3C objects, publishers SHOULD set delivery timeouts consistent with the media timeline. In MOQT, OBJECT_DELIVERY_TIMEOUT causes expired datagrams to be dropped. For objects with Delivery Mode Datagram, SUBGROUP_DELIVERY_TIMEOUT acts the same way as OBJECT_DELIVERY_TIMEOUT; if both are non-zero, the smaller value is used ([I-D.ietf-moq-transport-23], Section 5.2). This behavior allows obsolete V3C objects to be discarded instead of increasing latency. Datagram objects remain schedulable MOQT objects and therefore participate in MOQT priority scheduling. A V3C publisher SHOULD assign numerically lower publisher priority values to reconstruction- critical objects, such as atlas and base geometry or basemesh, and numerically higher priority values to enhancement objects, such as high-resolution attributes. Subscribers MAY use subscriber priority and filters to adjust delivery based on viewport, bandwidth, or rendering needs, including via REQUEST_UPDATE. You, et al. Expires 19 May 2027 [Page 25] Internet-Draft V3C over MOQT November 2026 5.7.1. Encoding Considerations for Datagram Delivery QUIC DATAGRAM frames cannot be fragmented [RFC9221]. When a publisher intends to send a coded V3C unit with Delivery Mode Datagram, the encoder and the MOQT packager therefore share a size budget: the OBJECT_DATAGRAM that carries the unit, including its object header, object properties, and payload, MUST fit in a single datagram. The applicable budget is the maximum datagram size of the sending MOQT session, which is itself limited by the underlying transport: * Native QUIC: an endpoint MUST NOT send a DATAGRAM frame larger than the max_datagram_frame_size transport parameter advertised by its peer ([RFC9221], Section 3). That parameter is the maximum size of a DATAGRAM frame, including the frame type, length, and payload. [RFC9221] further reduces the usable payload by max_udp_payload_size [RFC9000] and by the path Maximum Transmission Unit (MTU), because a DATAGRAM frame that does not fit in one QUIC packet cannot be sent. * WebTransport: the application is provided with the maximum datagram size it can send ([I-D.ietf-webtrans-overview], Section 4.2). WebTransport over HTTP/3 requires a non-zero max_datagram_frame_size ([I-D.ietf-webtrans-http3], Section 3) and places the application payload in an HTTP Datagram [I-D.ietf-webtrans-http3]. HTTP Datagram framing consumes part of the QUIC DATAGRAM frame, so the application payload is smaller than max_datagram_frame_size. Each MOQT session along the path between the original publisher and the end subscriber can have a different maximum datagram size. Relays can also add Object Properties, which increase the encoded object ([I-D.ietf-moq-transport-23], Section 11.2). A publisher SHOULD treat the local session maximum as an upper bound and leave headroom for the OBJECT_DATAGRAM header, object properties, QUIC or HTTP Datagram framing, and downstream sessions. When datagram delivery is used, a publisher SHOULD configure the video and atlas encoders so that: * each coded slice and each NAL unit is small enough that, after V3C packaging and MOQT object framing, it remains within that budget; * the coded V3C unit placed in one MOQT Object, typically one access unit that may contain one or more NAL units, likewise remains within that budget. You, et al. Expires 19 May 2027 [Page 26] Internet-Draft V3C over MOQT November 2026 Encoder controls that reduce slice and NAL unit size include limiting the coded data per slice or atlas tile. This document does not specify numeric encoder parameters. Constraining slice and NAL unit size is encoder configuration. It does not change the object mapping in Section 5.5: NAL units remain inside the object payload, and publishers still SHOULD NOT emit one MOQT Object per NAL unit solely to express codec framing. If a slice or NAL unit cannot be encoded within the budget, or if the resulting coded V3C unit remains larger than the budget, the publisher MUST use subgroup stream delivery for that object (Section 5.5). This document does not define fragmentation of a NAL unit or coded V3C unit across MOQT datagrams. Appendix A lists alternatives to that rule. 6. V3C Packaging This document defines the V3C packaging for carrying coded V3C units in MOQT Objects using MSF. When a track uses V3C packaging, the catalog packaging attribute ([I-D.ietf-moq-msf], Section 5.2.4) MUST be present and MUST have the value v3c (Section 7.1). Object payloads are the coded V3C units specified in Section 5.6. The payload is not a LOC sample and does not include a LOC header. V3C identifiers used for track selection are signaled in the track- level catalog object v3c (Section 7.2) and MUST NOT be carried in MOQT Object Properties. MOQT Object Properties remain limited to information relevant to Object distribution ([I-D.ietf-moq-transport-23], Section 11.1.2). V3C-packaged tracks MAY carry the following properties defined by [I-D.ietf-moq-loc]: TIMESCALE (0x08): The number of TIMESTAMP units per second, for example 1000 or 90000 ([I-D.ietf-moq-loc], Section 2.3.1.2). When used, it SHOULD be sent as a Track Property and SHOULD equal the catalog timescale value ([I-D.ietf-moq-msf], Section 5.2.21). TIMESTAMP (0x10): The presentation timestamp of the V3C composition unit whose coded V3C unit the Object carries, in TIMESCALE units ([I-D.ietf-moq-loc], Section 2.3.1.1). Corresponding Objects of time-aligned tracks carry the same value. These properties allow relays and subscribers to synchronize V3C tracks with other media and to manage playout buffers without parsing atlas or video payloads. You, et al. Expires 19 May 2027 [Page 27] Internet-Draft V3C over MOQT November 2026 7. Catalog Signaling for V3C Publishers advertise available tracks using the MSF catalog [I-D.ietf-moq-msf]. V3C publishers MUST include sufficient information for subscribers to (1) discover all required component tracks, (2) obtain the VPS and, with ISOBMFF framing, the decoder configuration of each track via initRef, (3) determine dependencies between tracks, and (4) select compatible alternatives. A subscriber uses catalog metadata to identify the V3C tracks it needs. It can subscribe to those tracks individually using SUBSCRIBE, or use SUBSCRIBE_TRACKS to request tracks within a namespace, optionally restricted by applicable MOQT Track Property filters. The subscriber can subsequently modify subscription parameters using REQUEST_UPDATE. 7.1. V3C packaging type This specification extends the allowed packaging values defined in [I-D.ietf-moq-msf] to include one new entry: +======+=======+===============+ | Name | Value | Reference | +======+=======+===============+ | V3C | v3c | This document | +------+-------+---------------+ Table 5: V3C packaging type Every Track entry in a catalog carrying V3C-packaged media data MUST declare a packaging type value of v3c. Object payloads of such tracks are as specified in Section 6. 7.2. V3C Track Identifiers [I-D.ietf-moq-msf] allows a producer to add catalog fields that do not collide with defined MSF names. This document defines a track- level object named v3c. Location: Track object. Required: Mandatory when packaging is v3c. JSON type: Object. You, et al. Expires 19 May 2027 [Page 28] Internet-Draft V3C over MOQT November 2026 The v3c object carries identifiers already present in the V3C unit header as specified in [ISOIEC23090-5]. [RFC10034], Section 4.3.1, copies an earlier header layout for informative purposes. Where that copy and [ISOIEC23090-5] differ, this document follows [ISOIEC23090-5]: unit types V3C_BMD and V3C_ADD are defined, and the packed-video header carries vuh_packed_map_index (8 bits) and 9 reserved bits rather than 17 reserved bits. A subscriber uses these identifiers to select tracks before any media object arrives. component is a string and unitType is a number. In multi-track mode, at least one of component or unitType MUST be present. unitType copies the 5-bit vuh_unit_type value from the V3C unit header as specified in [ISOIEC23090-5], Table 3. unitType MUST NOT be 0 (V3C_VPS) or a reserved value. When both component and unitType are present, they MUST identify the same unit type in Table 7. atlasId, mapIndex, packedMapIndex, attributeIndex, attributePartitionIndex, parameterSetId, auxiliaryVideo, and tileId are numbers. framing is a string. Presence follows the V3C unit header except as noted below. * atlasId is omitted for common-atlas. * mapIndex is omitted when the unit header does not include vuh_map_index, and when all maps of that component occupy one stream (Section 5.2.2). * packedMapIndex is used for packed video. It copies vuh_packed_map_index. It MAY be omitted when a single packed map is present. * attributeIndex and attributePartitionIndex are used for AVD. * auxiliaryVideo is used for geometry and attribute tracks. It copies vuh_auxiliary_video_flag. A value of 0 MAY be omitted; receivers infer 0 when the field is absent (Section 5.2.3). * parameterSetId is optional. * tileId is omitted unless the track is an atlas tile track (Section 5.2.4). It copies the atlas tile identifier (afti_tile_id in [ISOIEC23090-5]) of the tile carried by the track. It is not a V3C unit header field. * framing is a string that identifies the payload framing of the track (Section 5.6). Allowed values are native and isobmff. When the field is absent, receivers infer native. It is not a V3C unit header field. A receiver MUST NOT decode a track whose framing value it does not recognize. You, et al. Expires 19 May 2027 [Page 29] Internet-Draft V3C over MOQT November 2026 attributeIndex identifies which AVD component a track carries. The attribute type associated with that index is in the VPS (Section 5.3.2), not in this object. +=========================+========================================+ | Name | V3C syntax | +=========================+========================================+ | unitType | vuh_unit_type (5-bit value) | +-------------------------+----------------------------------------+ | component | vuh_unit_type | +-------------------------+----------------------------------------+ | atlasId | vuh_atlas_id | +-------------------------+----------------------------------------+ | mapIndex | vuh_map_index | +-------------------------+----------------------------------------+ | packedMapIndex | vuh_packed_map_index | +-------------------------+----------------------------------------+ | attributeIndex | vuh_attribute_index | +-------------------------+----------------------------------------+ | attributePartitionIndex | vuh_attribute_partition_index | +-------------------------+----------------------------------------+ | auxiliaryVideo | vuh_auxiliary_video_flag | +-------------------------+----------------------------------------+ | parameterSetId | vuh_v3c_parameter_set_id | +-------------------------+----------------------------------------+ | tileId | afti_tile_id (not a unit header field) | +-------------------------+----------------------------------------+ | framing | None (payload framing, not a V3C | | | syntax element) | +-------------------------+----------------------------------------+ Table 6: Fields of the catalog v3c object Allowed component values are: You, et al. Expires 19 May 2027 [Page 30] Internet-Draft V3C over MOQT November 2026 +==========+==============+======================+============+ | unitType | Value | V3C unit type | Identifier | +==========+==============+======================+============+ | 1 | atlas | Atlas data | V3C_AD | +----------+--------------+----------------------+------------+ | 2 | occupancy | Occupancy video data | V3C_OVD | +----------+--------------+----------------------+------------+ | 3 | geometry | Geometry video data | V3C_GVD | +----------+--------------+----------------------+------------+ | 4 | attribute | Attribute video data | V3C_AVD | +----------+--------------+----------------------+------------+ | 5 | packed | Packed video data | V3C_PVD | +----------+--------------+----------------------+------------+ | 6 | common-atlas | Common atlas data | V3C_CAD | +----------+--------------+----------------------+------------+ | 7 | basemesh | Basemesh data | V3C_BMD | +----------+--------------+----------------------+------------+ | 8 | displacement | Arithmetic-coded | V3C_ADD | | | | displacement data | | +----------+--------------+----------------------+------------+ Table 7: Allowed v3c.component values CAD payload syntax is specified in [ISOIEC23090-12]. Basemesh and displacement payload syntax is specified in [ISOIEC23090-29]. This document maps those unit types the same way it maps CAD: the unit type and catalog identity are generic; application reconstruction is out of scope. Reserved vuh_unit_type values 9 through 31 ([ISOIEC23090-5], Table 3) have no component value in this table. Unknown v3c fields MUST be ignored, consistent with MSF catalog parsing rules. Unknown component values MUST be ignored. For tracks with packaging equal to v3c, the MSF codec field ([I-D.ietf-moq-msf], Section 5.2.18) carries a value of the codecs parameter as used for the corresponding ISOBMFF track in [ISOIEC23090-10], rather than a WebCodecs codec string. The MSF requirement to use the WebCodecs codec registry applies only to LOC packaging. The codec value is never v3c. * Atlas tracks use a V3C sample entry type followed by the profile, tier, and level elements specified in [ISOIEC23090-10], Annex C, for example v3c1.L90.4.0.1. The sample entry type also indicates the array_completeness of atlas parameter sets in the V3CDecoderConfigurationRecord: v3c1 when all atlas parameter sets are in the record, and v3cg otherwise. Atlas tile tracks use v3t1 ([ISOIEC23090-10], Clause 7.3.2.2). You, et al. Expires 19 May 2027 [Page 31] Internet-Draft V3C over MOQT November 2026 * Video component tracks use the restricted video sample entry resv, the V3C video component scheme vvvc, and the original sample entry type of the video codec, for example resv.vvvc.hvc1 ([ISOIEC23090-10], Clause 7.3.3 and Annex D). The original sample entry type identifies the decoder configuration record that the track references with initRef. * Basemesh tracks use bmc1 or bmcg, and arithmetic-coded displacement tracks use acd1 or acdg ([ISOIEC23090-10], Clause 7.6.3). With native framing, no decoder configuration record is carried. The codec value then uses the sample entry type that allows parameter sets outside a decoder configuration record: v3cg for atlas tracks, a video sample entry type that allows in-band parameter sets (for example resv.vvvc.hev1 for HEVC [ISOIEC14496-15]), bmcg, or acdg. With native framing, the codec value identifies the codec, profile, tier, and level only; it does not indicate ISOBMFF encapsulation. | Editor's note: A codec identifier for native framing that does | not reuse ISOBMFF sample entry types may be preferable. 7.3. Track Roles Each V3C component track SHOULD indicate a role that reflects the carried component. [I-D.ietf-moq-msf] defines reserved roles such as video and audio, and permits custom roles that do not collide with those names. This document defines the following role strings: v3c-atlas, v3c-atlas-tile, v3c-occupancy, v3c-geometry, v3c- attribute, v3c-packed, v3c-common-atlas, v3c-basemesh, and v3c- displacement. These roles identify V3C component and unit types, not the semantic type of an attribute. [ISOIEC23090-5] defines rotation as ATTR_ROTATION, signaled by ai_attribute_type_id in the VPS, but the corresponding media unit remains an Attribute Video Data (V3C_AVD) unit. Consequently, a separate rotation track uses role v3c- attribute and identifies its attribute with v3c.attributeIndex; this specification does not define a v3c-rotation role. The same rule applies to texture, transparency, spherical harmonics, scale, and other V3C attribute types. When those attributes are carried as regions of a Packed Video Data (V3C_PVD) unit, the track instead uses role v3c-packed. You, et al. Expires 19 May 2027 [Page 32] Internet-Draft V3C over MOQT November 2026 7.4. Dependencies and Render Groups Tracks that are designed to be rendered together as one V3C presentation SHOULD share the same renderGroup value ([I-D.ietf-moq-msf], Section 5.2.11). renderGroup expresses association among all carried components of the same presentation, including atlas, occupancy, geometry, attribute, packed, common atlas, basemesh, and displacement tracks. vps_atlas_count_minus1 in the VPS MAY be greater than 0. CAD has no atlasId and applies to all atlases in the CVS. When a CAD track is present, each atlas track SHOULD list that CAD track in depends. Video, packed, basemesh, and displacement tracks list their atlas track, not the CAD track, in depends. Tracks that cannot be decoded or reconstructed without another track MUST list that track in depends ([I-D.ietf-moq-msf], Section 5.2.14). In particular, every video-coded V3C component track, packed video track, basemesh track, displacement track, and atlas tile track MUST list the corresponding atlas track. The VPS is reached through the atlas track: the atlas track references it with initRef, and other component tracks list the atlas track in depends. A receiver that subscribes to geometry, packed video, or basemesh without the dependent atlas track, or without the referenced VPS, cannot reconstruct volumetric frames. Publishers MAY still offer such a subscription so that a receiver can cache or preview a component; reconstruction requirements are unchanged. 7.5. Alternate Groups When multiple tracks provide alternate encodings of the same V3C component (for example geometry at several bitrates), they MUST share the same altGroup value ([I-D.ietf-moq-msf], Section 5.2.12) and MUST be time-aligned as required by MSF for alternate groups. A subscriber SHOULD select at most one track per altGroup. Geometry alternatives and attribute alternatives MUST NOT be forced into a single altGroup solely because they belong to the same V3C presentation. Independent altGroup values allow a subscriber to combine, for example, high-bitrate geometry with low-bitrate attributes. When selecting alternatives, the subscriber MUST also select a compatible atlas track and VPS. [ISOIEC23090-29] encodes V-DMC displacement either as geometry video or as arithmetic-coded displacement. Those forms are mutually exclusive for one atlas in the VPS. When a publisher offers both forms, the geometry track (V3C_GVD, role v3c-geometry) and the You, et al. Expires 19 May 2027 [Page 33] Internet-Draft V3C over MOQT November 2026 arithmetic-coded displacement track (V3C_ADD, role v3c-displacement) MUST share one altGroup and MUST be time-aligned. Each track MUST list, in depends, the atlas track and basemesh track that match that displacement form, and that atlas track MUST reference with initRef initialization data whose VPS indicates that displacement form. A subscriber MUST select at most one of the two tracks and MUST select those dependent tracks and that initialization data. Section 7.6.4 shows the arithmetic-coded displacement form. 7.6. Catalog Examples The following examples are informative. Each describes a 50-frame presentation at 25 frames per second. The active VPS determines which component tracks are present. The examples use the recommended naming patterns in Figure 2, but MOQT treats track names as opaque identifiers and does not infer component semantics from them. Within one example, every media track shares renderGroup 1, isLive false, the same namespace, and the same media timeline. Except for Section 7.6.2, the examples use ISOBMFF framing (Section 5.6.2), and every v3c object therefore contains "framing": "isobmff". The atlas track references the V3CDecoderConfigurationRecord entry atlas-init, and the video component tracks reference the HEVCDecoderConfigurationRecord entry hevc-init (Section 5.3). For brevity, all video component tracks in an example share one video decoder configuration; a publisher whose components use different video configurations provides one entry per configuration. The data values are placeholders, not working configuration records. Attribute types are recovered from the VPS (Section 5.3.2), not from the track name. The atlas track codec value v3c1 indicates that all atlas parameter sets are in the V3CDecoderConfigurationRecord; the profile, tier, and level elements of the codecs value ([ISOIEC23090-10], Annex C) are omitted for brevity. Video component tracks use codec "resv.vvvc.hvc1": You, et al. Expires 19 May 2027 [Page 34] Internet-Draft V3C over MOQT November 2026 +=========+===================================================+ | Element | Meaning | +=========+===================================================+ | resv | Restricted video sample entry ([ISOIEC14496-12]). | | | The samples are not plain 2D video. | +---------+---------------------------------------------------+ | vvvc | Restriction scheme for a V3C video component | | | ([ISOIEC23090-10]): occupancy, geometry, | | | attribute, or packed video. | +---------+---------------------------------------------------+ | hvc1 | The video is HEVC/H.265 with parameter sets | | | carried in the HEVCDecoderConfigurationRecord | | | ([ISOIEC14496-15]), here referenced by initRef. | +---------+---------------------------------------------------+ Table 8: Elements of the example video codec value MSF expresses both trackDuration and the template's deltaMediaTime in milliseconds ([I-D.ietf-moq-msf], Section 7.4.1). For these examples: frame duration = 1000 / 25 = 40 ms frame count = trackDuration / deltaMediaTime = 2000 / 40 = 50 The template [0, 40, [1, 0], [0, 1], 0, 0] therefore describes entry indices n from 0 through 49: mediaTime[n] = n * 40 ms location[n] = [1, n] In these examples, the whole presentation is one run of 50 composition units that starts with an IRAP composition unit, so it is carried in a single Group 1 (Section 5.4). The first frame starts at 0 ms at Group 1, Object 0. The last frame starts at 1960 ms at Group 1, Object 49 and ends at the 2000 ms track duration. A FETCH covering all 50 Objects uses a start Location [1, 0] and an inclusive end Location [1, 49] ([I-D.ietf-moq-transport-23]). The timescale value does not scale these template values; the template interval is explicitly in milliseconds. The examples in Section 7.6.1 and Section 7.6.3 illustrate Gaussian splatting content conforming to the V-PCC GS or V-PCC GS Still toolset profile component of [ISOIEC23090-5]. Annex A of [ISOIEC23090-5] identifies those profile components and their profile, tier, and level signaling; Annex H specifies their V-PCC restrictions and reconstruction processes. The mapping in this You, et al. Expires 19 May 2027 [Page 35] Internet-Draft V3C over MOQT November 2026 document is not limited to those profiles. The packed and unpacked component organizations are determined by the component-presence flags and packed-video extension in the active VPS, not by the catalog. A subscriber MAY request a subset of the advertised tracks. A track listed in depends that is not requested cannot be used to reconstruct the dependent component (Section 7.4). Alternate encodings of one component share altGroup and are not shown (Section 7.5). A mesh presentation MAY advertise a basemesh track together with either a geometry track, when that track carries video-coded displacement, or an arithmetic-coded displacement track. 7.6.1. Packed Video Component Mode Figure 7 shows a presentation in which attribute data is carried in packed video and geometry remains its own sub-bitstream. The active VPS has geometry video and packed video present. It does not have separate occupancy or attribute video sub-bitstreams, so those tracks are omitted (Section 5.2.1). The geometry and packed tracks list the atlas track in depends. Regions inside the packed frame, including which attributes they carry, are recovered from the VPS packed-video extension specified by [ISOIEC23090-5]. { "version": "draft-01", "tracks": [ { "namespace": "packed", "name": "v3c/atlas/0", "packaging": "v3c", "isLive": false, "role": "v3c-atlas", "renderGroup": 1, "initRef": "atlas-init", "codec": "v3c1", "framerate": 25, "timescale": 1000, "trackDuration": 2000, "template": [0, 40, [1, 0], [0, 1], 0, 0], "v3c": { "framing": "isobmff", "component": "atlas", "unitType": 1, "atlasId": 0 } }, { You, et al. Expires 19 May 2027 [Page 36] Internet-Draft V3C over MOQT November 2026 "namespace": "packed", "name": "v3c/geometry/0", "packaging": "v3c", "isLive": false, "role": "v3c-geometry", "renderGroup": 1, "initRef": "hevc-init", "depends": ["v3c/atlas/0"], "codec": "resv.vvvc.hvc1", "bitrate": 4000000, "framerate": 25, "timescale": 1000, "trackDuration": 2000, "template": [0, 40, [1, 0], [0, 1], 0, 0], "v3c": { "framing": "isobmff", "component": "geometry", "unitType": 3, "atlasId": 0 } }, { "namespace": "packed", "name": "v3c/packed/0/0", "packaging": "v3c", "isLive": false, "role": "v3c-packed", "renderGroup": 1, "initRef": "hevc-init", "depends": ["v3c/atlas/0"], "codec": "resv.vvvc.hvc1", "bitrate": 8000000, "framerate": 25, "timescale": 1000, "trackDuration": 2000, "template": [0, 40, [1, 0], [0, 1], 0, 0], "v3c": { "framing": "isobmff", "component": "packed", "unitType": 5, "atlasId": 0, "packedMapIndex": 0 } } ], "initDataList": [ { "id": "atlas-init", You, et al. Expires 19 May 2027 [Page 37] Internet-Draft V3C over MOQT November 2026 "type": "inline", "data": "PLACEHOLDER-V3CDecoderConfigurationRecord" }, { "id": "hevc-init", "type": "inline", "data": "PLACEHOLDER-HEVCDecoderConfigurationRecord" } ] } Figure 7: Catalog when attributes are packed 7.6.2. Packed Video Component Mode with Native Framing Figure 8 shows the presentation of Section 7.6.1 with native framing (Section 5.6.1). The atlas track references the entry vps, which contains the v3c_parameter_set() of the active VPS. The geometry and packed tracks have no initRef; their HEVC parameter sets are carried in band, and their codec value uses the sample entry type hev1 (Section 7.2). The atlas track codec value is v3cg. The data value is a placeholder. { "version": "draft-01", "tracks": [ { "namespace": "packed-native", "name": "v3c/atlas/0", "packaging": "v3c", "isLive": false, "role": "v3c-atlas", "renderGroup": 1, "initRef": "vps", "codec": "v3cg", "framerate": 25, "timescale": 1000, "trackDuration": 2000, "template": [0, 40, [1, 0], [0, 1], 0, 0], "v3c": { "framing": "native", "component": "atlas", "unitType": 1, "atlasId": 0 } }, { "namespace": "packed-native", You, et al. Expires 19 May 2027 [Page 38] Internet-Draft V3C over MOQT November 2026 "name": "v3c/geometry/0", "packaging": "v3c", "isLive": false, "role": "v3c-geometry", "renderGroup": 1, "depends": ["v3c/atlas/0"], "codec": "resv.vvvc.hev1", "bitrate": 4000000, "framerate": 25, "timescale": 1000, "trackDuration": 2000, "template": [0, 40, [1, 0], [0, 1], 0, 0], "v3c": { "framing": "native", "component": "geometry", "unitType": 3, "atlasId": 0 } }, { "namespace": "packed-native", "name": "v3c/packed/0/0", "packaging": "v3c", "isLive": false, "role": "v3c-packed", "renderGroup": 1, "depends": ["v3c/atlas/0"], "codec": "resv.vvvc.hev1", "bitrate": 8000000, "framerate": 25, "timescale": 1000, "trackDuration": 2000, "template": [0, 40, [1, 0], [0, 1], 0, 0], "v3c": { "framing": "native", "component": "packed", "unitType": 5, "atlasId": 0, "packedMapIndex": 0 } } ], "initDataList": [ { "id": "vps", "type": "inline", "data": "PLACEHOLDER-v3c_parameter_set" } You, et al. Expires 19 May 2027 [Page 39] Internet-Draft V3C over MOQT November 2026 ] } Figure 8: Catalog with native framing 7.6.3. Unpacked Component Mode with Multiple Attributes Figure 9 shows the same content with packed video absent (vps_packed_video_present_flag equal to 0) and every video component carried on its own track. The active VPS has occupancy video, geometry video, and attribute video present. Each attribute index is one AVD track. For this example, the VPS maps the attribute indices as follows: * 0: texture (color) * 1: transparency (opacity in Gaussian splat terminology) * 2: scale * 3: rotation * 4: spherical harmonics These are attribute indices, not the numeric ai_attribute_type_id values. The corresponding ATTR_TEXTURE, ATTR_TRANSPARENCY, ATTR_SCALE, ATTR_ROTATION, and ATTR_SPHERICAL_HARMONICS types, and the equivalence of transparency and Gaussian splat opacity, are defined by [ISOIEC23090-5]. Each video track lists v3c/atlas/0 in depends. mapIndex is omitted because the VPS signals a single map (vps_map_count_minus1 equal to 0; Section 5.2.2). attributePartitionIndex is 0 because none of these attributes is split across partitions. { "version": "draft-01", "tracks": [ { "namespace": "unpacked", "name": "v3c/atlas/0", "packaging": "v3c", "isLive": false, "role": "v3c-atlas", "renderGroup": 1, "initRef": "atlas-init", "codec": "v3c1", "framerate": 25, You, et al. Expires 19 May 2027 [Page 40] Internet-Draft V3C over MOQT November 2026 "timescale": 1000, "trackDuration": 2000, "template": [0, 40, [1, 0], [0, 1], 0, 0], "v3c": { "framing": "isobmff", "component": "atlas", "unitType": 1, "atlasId": 0 } }, { "namespace": "unpacked", "name": "v3c/occupancy/0", "packaging": "v3c", "isLive": false, "role": "v3c-occupancy", "renderGroup": 1, "initRef": "hevc-init", "depends": ["v3c/atlas/0"], "codec": "resv.vvvc.hvc1", "bitrate": 500000, "framerate": 25, "timescale": 1000, "trackDuration": 2000, "template": [0, 40, [1, 0], [0, 1], 0, 0], "v3c": { "framing": "isobmff", "component": "occupancy", "unitType": 2, "atlasId": 0 } }, { "namespace": "unpacked", "name": "v3c/geometry/0", "packaging": "v3c", "isLive": false, "role": "v3c-geometry", "renderGroup": 1, "initRef": "hevc-init", "depends": ["v3c/atlas/0"], "codec": "resv.vvvc.hvc1", "bitrate": 4000000, "framerate": 25, "timescale": 1000, "trackDuration": 2000, "template": [0, 40, [1, 0], [0, 1], 0, 0], "v3c": { You, et al. Expires 19 May 2027 [Page 41] Internet-Draft V3C over MOQT November 2026 "framing": "isobmff", "component": "geometry", "unitType": 3, "atlasId": 0 } }, { "namespace": "unpacked", "name": "v3c/attribute/0/0/0", "packaging": "v3c", "isLive": false, "role": "v3c-attribute", "renderGroup": 1, "initRef": "hevc-init", "depends": ["v3c/atlas/0"], "codec": "resv.vvvc.hvc1", "bitrate": 3000000, "framerate": 25, "timescale": 1000, "trackDuration": 2000, "template": [0, 40, [1, 0], [0, 1], 0, 0], "v3c": { "framing": "isobmff", "component": "attribute", "unitType": 4, "atlasId": 0, "attributeIndex": 0, "attributePartitionIndex": 0 } }, { "namespace": "unpacked", "name": "v3c/attribute/0/1/0", "packaging": "v3c", "isLive": false, "role": "v3c-attribute", "renderGroup": 1, "initRef": "hevc-init", "depends": ["v3c/atlas/0"], "codec": "resv.vvvc.hvc1", "bitrate": 1000000, "framerate": 25, "timescale": 1000, "trackDuration": 2000, "template": [0, 40, [1, 0], [0, 1], 0, 0], "v3c": { "framing": "isobmff", "component": "attribute", You, et al. Expires 19 May 2027 [Page 42] Internet-Draft V3C over MOQT November 2026 "unitType": 4, "atlasId": 0, "attributeIndex": 1, "attributePartitionIndex": 0 } }, { "namespace": "unpacked", "name": "v3c/attribute/0/2/0", "packaging": "v3c", "isLive": false, "role": "v3c-attribute", "renderGroup": 1, "initRef": "hevc-init", "depends": ["v3c/atlas/0"], "codec": "resv.vvvc.hvc1", "bitrate": 1000000, "framerate": 25, "timescale": 1000, "trackDuration": 2000, "template": [0, 40, [1, 0], [0, 1], 0, 0], "v3c": { "framing": "isobmff", "component": "attribute", "unitType": 4, "atlasId": 0, "attributeIndex": 2, "attributePartitionIndex": 0 } }, { "namespace": "unpacked", "name": "v3c/attribute/0/3/0", "packaging": "v3c", "isLive": false, "role": "v3c-attribute", "renderGroup": 1, "initRef": "hevc-init", "depends": ["v3c/atlas/0"], "codec": "resv.vvvc.hvc1", "bitrate": 1000000, "framerate": 25, "timescale": 1000, "trackDuration": 2000, "template": [0, 40, [1, 0], [0, 1], 0, 0], "v3c": { "framing": "isobmff", "component": "attribute", You, et al. Expires 19 May 2027 [Page 43] Internet-Draft V3C over MOQT November 2026 "unitType": 4, "atlasId": 0, "attributeIndex": 3, "attributePartitionIndex": 0 } }, { "namespace": "unpacked", "name": "v3c/attribute/0/4/0", "packaging": "v3c", "isLive": false, "role": "v3c-attribute", "renderGroup": 1, "initRef": "hevc-init", "depends": ["v3c/atlas/0"], "codec": "resv.vvvc.hvc1", "bitrate": 2000000, "framerate": 25, "timescale": 1000, "trackDuration": 2000, "template": [0, 40, [1, 0], [0, 1], 0, 0], "v3c": { "framing": "isobmff", "component": "attribute", "unitType": 4, "atlasId": 0, "attributeIndex": 4, "attributePartitionIndex": 0 } } ], "initDataList": [ { "id": "atlas-init", "type": "inline", "data": "PLACEHOLDER-V3CDecoderConfigurationRecord" }, { "id": "hevc-init", "type": "inline", "data": "PLACEHOLDER-HEVCDecoderConfigurationRecord" } ] } Figure 9: Catalog when every component is its own track You, et al. Expires 19 May 2027 [Page 44] Internet-Draft V3C over MOQT November 2026 7.6.4. Video-based Dynamic Mesh Coding (V-DMC) Figure 10 shows a V-DMC presentation ([ISOIEC23090-29]) following the multi-track layout of [ISOIEC23090-10], Clause 7.6.3. The presentation consists of an atlas track, a basemesh track, an arithmetic-coded displacement track, and a texture attribute video track. The basemesh and displacement tracks reference their own decoder configuration records (BaseMeshDecoderConfigurationRecord and ACDisplacementDecoderConfigurationRecord), and their codec values are the corresponding sample entry types bmc1 and acd1 (Section 7.2). The VPS in atlas-init carries a V-DMC VPS extension and a ptl_profile_toolset_idc in the range reserved for V-DMC. When displacement is coded with a video codec instead, [ISOIEC23090-10] carries it in a video component track with vuh_unit_type equal to V3C_GVD. { "version": "draft-01", "tracks": [ { "namespace": "vdmc", "name": "v3c/atlas/0", "packaging": "v3c", "isLive": false, "role": "v3c-atlas", "renderGroup": 1, "initRef": "atlas-init", "codec": "v3c1", "framerate": 25, "timescale": 1000, "trackDuration": 2000, "template": [0, 40, [1, 0], [0, 1], 0, 0], "v3c": { "framing": "isobmff", "component": "atlas", "unitType": 1, "atlasId": 0 } }, { "namespace": "vdmc", "name": "v3c/basemesh/0", "packaging": "v3c", "isLive": false, "role": "v3c-basemesh", "renderGroup": 1, "initRef": "basemesh-init", "depends": ["v3c/atlas/0"], You, et al. Expires 19 May 2027 [Page 45] Internet-Draft V3C over MOQT November 2026 "codec": "bmc1", "framerate": 25, "timescale": 1000, "trackDuration": 2000, "template": [0, 40, [1, 0], [0, 1], 0, 0], "v3c": { "framing": "isobmff", "component": "basemesh", "unitType": 7, "atlasId": 0 } }, { "namespace": "vdmc", "name": "v3c/displacement/0", "packaging": "v3c", "isLive": false, "role": "v3c-displacement", "renderGroup": 1, "initRef": "displacement-init", "depends": ["v3c/atlas/0", "v3c/basemesh/0"], "codec": "acd1", "framerate": 25, "timescale": 1000, "trackDuration": 2000, "template": [0, 40, [1, 0], [0, 1], 0, 0], "v3c": { "framing": "isobmff", "component": "displacement", "unitType": 8, "atlasId": 0 } }, { "namespace": "vdmc", "name": "v3c/attribute/0/0/0", "packaging": "v3c", "isLive": false, "role": "v3c-attribute", "renderGroup": 1, "initRef": "hevc-init", "depends": ["v3c/atlas/0"], "codec": "resv.vvvc.hvc1", "bitrate": 3000000, "framerate": 25, "timescale": 1000, "trackDuration": 2000, "template": [0, 40, [1, 0], [0, 1], 0, 0], You, et al. Expires 19 May 2027 [Page 46] Internet-Draft V3C over MOQT November 2026 "v3c": { "framing": "isobmff", "component": "attribute", "unitType": 4, "atlasId": 0, "attributeIndex": 0, "attributePartitionIndex": 0 } } ], "initDataList": [ { "id": "atlas-init", "type": "inline", "data": "PLACEHOLDER-V3CDecoderConfigurationRecord" }, { "id": "basemesh-init", "type": "inline", "data": "PLACEHOLDER-BaseMeshDecoderConfigurationRecord" }, { "id": "displacement-init", "type": "inline", "data": "PLACEHOLDER-ACDisplacementDecoderConfigurationRecord" }, { "id": "hevc-init", "type": "inline", "data": "PLACEHOLDER-HEVCDecoderConfigurationRecord" } ] } Figure 10: Catalog for a V-DMC presentation The displacement track lists the basemesh track in depends because displacements are applied to the decoded basemesh during V-DMC reconstruction ([ISOIEC23090-29]). 7.6.5. Spatial Subdivision with Atlas Tile Tracks Figure 11 follows the layout of the multi-track example with atlas tile tracks in [ISOIEC23090-10], Annex D.4, without an occupancy component. The atlas frame is partitioned into two atlas tiles with tile identifiers 1 and 2. One atlas track carries the atlas parameter sets and the non-ACL NAL units, and one atlas tile track per tile carries the ACL NAL units of that tile (Section 5.2.4). For You, et al. Expires 19 May 2027 [Page 47] Internet-Draft V3C over MOQT November 2026 each tile, a geometry track and an attribute track carry the video components of the corresponding region. The tile tracks use the codec value v3t1 and reference the same initDataList entry as the atlas track. The two geometry tracks carry the same V3C unit header fields; they are distinguished by the atlas tile track that each lists in depends. The same applies to the two attribute tracks. The video track names extend the recommended patterns with a /tile/ suffix. A subscriber interested in only one spatial region subscribes to the atlas track, one atlas tile track, and the video tracks that depend on that tile track. { "version": "draft-01", "tracks": [ { "namespace": "tiled", "name": "v3c/atlas/0", "packaging": "v3c", "isLive": false, "role": "v3c-atlas", "renderGroup": 1, "initRef": "atlas-init", "codec": "v3c1", "framerate": 25, "timescale": 1000, "trackDuration": 2000, "template": [0, 40, [1, 0], [0, 1], 0, 0], "v3c": { "framing": "isobmff", "component": "atlas", "unitType": 1, "atlasId": 0 } }, { "namespace": "tiled", "name": "v3c/atlas/0/tile/1", "packaging": "v3c", "isLive": false, "role": "v3c-atlas", "renderGroup": 1, "initRef": "atlas-init", "depends": ["v3c/atlas/0"], "codec": "v3t1", "framerate": 25, "timescale": 1000, You, et al. Expires 19 May 2027 [Page 48] Internet-Draft V3C over MOQT November 2026 "trackDuration": 2000, "template": [0, 40, [1, 0], [0, 1], 0, 0], "v3c": { "framing": "isobmff", "component": "atlas", "unitType": 1, "atlasId": 0, "tileId": 1 } }, { "namespace": "tiled", "name": "v3c/atlas/0/tile/2", "packaging": "v3c", "isLive": false, "role": "v3c-atlas", "renderGroup": 1, "initRef": "atlas-init", "depends": ["v3c/atlas/0"], "codec": "v3t1", "framerate": 25, "timescale": 1000, "trackDuration": 2000, "template": [0, 40, [1, 0], [0, 1], 0, 0], "v3c": { "framing": "isobmff", "component": "atlas", "unitType": 1, "atlasId": 0, "tileId": 2 } }, { "namespace": "tiled", "name": "v3c/geometry/0/tile/1", "packaging": "v3c", "isLive": false, "role": "v3c-geometry", "renderGroup": 1, "initRef": "hevc-init", "depends": ["v3c/atlas/0", "v3c/atlas/0/tile/1"], "codec": "resv.vvvc.hvc1", "bitrate": 2000000, "framerate": 25, "timescale": 1000, "trackDuration": 2000, "template": [0, 40, [1, 0], [0, 1], 0, 0], "v3c": { You, et al. Expires 19 May 2027 [Page 49] Internet-Draft V3C over MOQT November 2026 "framing": "isobmff", "component": "geometry", "unitType": 3, "atlasId": 0 } }, { "namespace": "tiled", "name": "v3c/attribute/0/0/0/tile/1", "packaging": "v3c", "isLive": false, "role": "v3c-attribute", "renderGroup": 1, "initRef": "hevc-init", "depends": ["v3c/atlas/0", "v3c/atlas/0/tile/1"], "codec": "resv.vvvc.hvc1", "bitrate": 1500000, "framerate": 25, "timescale": 1000, "trackDuration": 2000, "template": [0, 40, [1, 0], [0, 1], 0, 0], "v3c": { "framing": "isobmff", "component": "attribute", "unitType": 4, "atlasId": 0, "attributeIndex": 0, "attributePartitionIndex": 0 } }, { "namespace": "tiled", "name": "v3c/geometry/0/tile/2", "packaging": "v3c", "isLive": false, "role": "v3c-geometry", "renderGroup": 1, "initRef": "hevc-init", "depends": ["v3c/atlas/0", "v3c/atlas/0/tile/2"], "codec": "resv.vvvc.hvc1", "bitrate": 2000000, "framerate": 25, "timescale": 1000, "trackDuration": 2000, "template": [0, 40, [1, 0], [0, 1], 0, 0], "v3c": { "framing": "isobmff", "component": "geometry", You, et al. Expires 19 May 2027 [Page 50] Internet-Draft V3C over MOQT November 2026 "unitType": 3, "atlasId": 0 } }, { "namespace": "tiled", "name": "v3c/attribute/0/0/0/tile/2", "packaging": "v3c", "isLive": false, "role": "v3c-attribute", "renderGroup": 1, "initRef": "hevc-init", "depends": ["v3c/atlas/0", "v3c/atlas/0/tile/2"], "codec": "resv.vvvc.hvc1", "bitrate": 1500000, "framerate": 25, "timescale": 1000, "trackDuration": 2000, "template": [0, 40, [1, 0], [0, 1], 0, 0], "v3c": { "framing": "isobmff", "component": "attribute", "unitType": 4, "atlasId": 0, "attributeIndex": 0, "attributePartitionIndex": 0 } } ], "initDataList": [ { "id": "atlas-init", "type": "inline", "data": "PLACEHOLDER-V3CDecoderConfigurationRecord" }, { "id": "hevc-init", "type": "inline", "data": "PLACEHOLDER-HEVCDecoderConfigurationRecord" } ] } Figure 11: Catalog with atlas tile tracks You, et al. Expires 19 May 2027 [Page 51] Internet-Draft V3C over MOQT November 2026 8. Prioritization Considerations MOQT supports prioritization of delivery under congestion through subscriber priority and publisher priority ([I-D.ietf-moq-transport-23], Section 5.1). Priority values range from 0 to 255, where lower numeric values indicate higher priority. Publisher priority can be provided as a default track property (DEFAULT_PUBLISHER_PRIORITY) and can also be set per subgroup or datagram. A V3C publisher SHOULD assign higher priority, using lower numeric values, to components that are critical for reconstruction, such as atlas and base geometry or basemesh. Enhancement components, such as high-resolution attributes or optional packed-video refinements, SHOULD be assigned lower priority. When ptl_priority_order_enable_flag in the VPS is 1, [ISOIEC23090-5] defines a priority order among video components: geometry, then attribute components in increasing attribute index and partition index, then packed video components in increasing packed map index. A publisher SHOULD assign publisher priorities to video component tracks that are consistent with that order. Single-track mode (Appendix B) does not allow per-component prioritization. In datagram mode, reconstruction-critical datagrams SHOULD be prioritized over optional enhancement datagrams. Subscribers MAY adjust priorities dynamically based on viewport, bandwidth, rendering requirements, or selected alternatives, including by sending REQUEST_UPDATE. For example, if V3C tiles are exposed as separate tracks, subgroups, or datagram objects, a subscriber can prioritize tiles in or near the current viewport and deprioritize less relevant tiles. 9. Relationship to the RTP Payload Format for V3C [RFC10034] defines an RTP payload format for V3C atlas sub-bitstreams and uses SDP to carry the VPS and V3C unit-header identity. RTP payload formats for V3C video sub-bitstreams are defined by the relevant RTP payload formats for the applicable video codecs. This document provides the corresponding functions with MSF catalog fields rather than SDP: * the initialization data referenced by the atlas track initRef replaces sprop-v3c-parameter-set. With native framing, it carries the same v3c_parameter_set() value. With ISOBMFF framing, it is a V3CDecoderConfigurationRecord, whose setup unit arrays correspond to sprop-v3c-atlas-data. The VPS remains the source of attribute type, presence flags, and PTL, as in SDP; You, et al. Expires 19 May 2027 [Page 52] Internet-Draft V3C over MOQT November 2026 * the catalog v3c object replaces sprop-v3c-unit-type, sprop-v3c- atlas-id, sprop-v3c-attr-idx, sprop-v3c-attr-part-idx, sprop-v3c- map-idx, sprop-v3c-aux-video-flag, and related parameters. As with sprop-v3c-attr-idx, attributeIndex is an index; the type is in the VPS (Section 5.3.2). auxiliaryVideo replaces sprop-v3c- aux-video-flag. parameterSetId replaces sprop-v3c-vps-id. packedMapIndex has no SDP counterpart in [RFC10034] because that RFC's informative unit header treated packed-video bits as reserved; * tileId, when used, replaces sprop-v3c-tile-id for an optional per- tile atlas track (Section 5.2.4); * renderGroup and depends replace the RTP grouping mechanism that identifies streams of one V3C representation ([RFC10034], Section 9.3); * MOQT Groups replace RTP timestamp alignment for the V3C composition unit. RTP-style NAL fragmentation across packets is not reused. Oversized coded units use MOQT subgroup streams (Section 5.5). When datagram delivery is used, slice and NAL unit size SHOULD be constrained at encode time rather than by fragmenting NAL units across datagrams (Section 5.7.1). 10. Security Considerations This document inherits the security considerations of MOQT [I-D.ietf-moq-transport-23], QUIC [RFC9000], and MSF [I-D.ietf-moq-msf]. In particular, publishers and relays must consider resource exhaustion attacks caused by large numbers of tracks, objects, subgroups, or datagrams, and must validate bounds before allocating memory. Authentication, authorization, and confidentiality of MOQT sessions are provided by the underlying QUIC or WebTransport mapping. Object payloads remain opaque to relays. When end-to-end confidentiality and integrity of media are required, deployments can use the MSF content-protection mechanisms, including MoQ Secure Objects [I-D.ietf-moq-secure-objects] as referenced by [I-D.ietf-moq-msf]. The VPS and any component decoder configuration records in initDataList are catalog payload. An attacker that tampers with them can cause decoder misconfiguration or reconstruction failure. Catalog objects and initialization data MUST be protected with at least the same integrity guarantees as the component media they initialize. You, et al. Expires 19 May 2027 [Page 53] Internet-Draft V3C over MOQT November 2026 Before decoding, a receiver MUST verify that the catalog is consistent: every depends entry and initRef value resolves to a track or initDataList entry advertised in the same catalog and namespace, and the v3c identifiers of each track agree with the components that the VPS signals as present. Accepting a substituted atlas track or VPS is a cross-component integrity failure: geometry might be reconstructed against attacker-chosen patch metadata. Datagram delivery can increase the rate of object loss under congestion and can cause receivers to observe incomplete sets of V3C components for a given volumetric frame. Implementations SHOULD validate component dependencies before decoding or rendering and SHOULD tolerate missing optional datagram-delivered objects. Incomplete geometry, packed video, or atlas data MUST NOT be treated as a complete volumetric frame. Replay of an old Group under a current VPS, or of a current Group under a stale VPS, can produce incorrect reconstruction. Subscribers SHOULD bind decoded Groups to the catalog generation that advertised their initRef. A downgrade to packaging loc on a V3C component track would strip V3C identity from the catalog. A subscriber MUST NOT decode a track as a V3C component unless its packaging is v3c; this includes tracks that carry a V3C role (Section 7.3) or a v3c object with another packaging value. Relay-visible track and object metadata, including track names, priorities, and subscription filters, can reveal information about scene structure or user interest (for example, which attribute or viewport-related tracks are requested). Deployments that consider this sensitive should avoid placing viewport or tile identity in relay-visible properties and should consider end-to-end object protection. 11. IANA Considerations This document has no IANA actions at this time. [I-D.ietf-moq-msf] does not currently establish IANA registries for catalog packaging values or track roles. This document defines v3c as an extension packaging value (Section 7.1) and uses the custom role values defined in Section 7.3, as permitted by MSF. If MSF establishes registries for packaging values or track roles in a future revision, registration of these values can be requested at that time. 12. References 12.1. Normative References You, et al. Expires 19 May 2027 [Page 54] Internet-Draft V3C over MOQT November 2026 [I-D.ietf-moq-loc] Zanaty, M., Nandakumar, S., and P. Thatcher, "Low Overhead Media Container", Work in Progress, Internet-Draft, draft- ietf-moq-loc-05, 2 November 2026, . [I-D.ietf-moq-msf] Law, W. and S. Nandakumar, "MOQT Streaming Format", Work in Progress, Internet-Draft, draft-ietf-moq-msf-01, 2 June 2026, . [I-D.ietf-moq-transport-23] Nandakumar, S., Vasiliev, V., Swett, I., and A. Frindell, "Media over QUIC Transport", Work in Progress, Internet- Draft, draft-ietf-moq-transport-23, 2 November 2026, . [ISOIEC14496-15] ISO/IEC, "Information technology -- Coding of audio-visual objects -- Part 15: Carriage of network abstraction layer (NAL) unit structured video in the ISO base media file format", ISO/IEC 14496-15, n.d.. [ISOIEC23090-5] ISO/IEC, "Information technology -- Coded representation of immersive media -- Part 5: Visual volumetric video- based coding (V3C) and video-based point cloud compression (V-PCC)", ISO/IEC 23090-5:2026, 2026, . [ISOIEC23090-10] ISO/IEC, "Information technology -- Coded representation of immersive media -- Part 10: Carriage of visual volumetric video-based coding data", ISO/IEC 23090-10:2026 (DIS), 2026. [ISOIEC23090-29] ISO/IEC, "Information technology -- Coded representation of immersive media -- Part 29: Video-based dynamic mesh coding (V-DMC)", ISO/IEC 23090-29:2026, 2026, . You, et al. Expires 19 May 2027 [Page 55] Internet-Draft V3C over MOQT November 2026 [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, DOI 10.17487/RFC2119, March 1997, . [RFC4648] Josefsson, S., "The Base16, Base32, and Base64 Data Encodings", RFC 4648, DOI 10.17487/RFC4648, October 2006, . [RFC8174] Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC 2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174, May 2017, . [RFC9000] Iyengar, J., Ed. and M. Thomson, Ed., "QUIC: A UDP-Based Multiplexed and Secure Transport", RFC 9000, DOI 10.17487/RFC9000, May 2021, . [RFC9221] Pauly, T., Kinnear, E., and D. Schinazi, "An Unreliable Datagram Extension to QUIC", RFC 9221, DOI 10.17487/RFC9221, March 2022, . 12.2. Informative References [I-D.ietf-moq-cmsf] Law, W., "CMSF- a CMAF compliant implementation of MOQT Streaming Format", Work in Progress, Internet-Draft, draft-ietf-moq-cmsf-01, 3 June 2026, . [I-D.ietf-moq-secure-objects] Jennings, C. F., Nandakumar, S., and R. Barnes, "End-to- End Secure Objects for Media over QUIC Transport", Work in Progress, Internet-Draft, draft-ietf-moq-secure-objects- 01, 6 July 2026, . [I-D.ietf-webtrans-http3] Frindell, A., Kinnear, E., and V. Vasiliev, "WebTransport over HTTP/3", Work in Progress, Internet-Draft, draft- ietf-webtrans-http3-17, 2 November 2026, . You, et al. Expires 19 May 2027 [Page 56] Internet-Draft V3C over MOQT November 2026 [I-D.ietf-webtrans-overview] Kinnear, E. and V. Vasiliev, "The WebTransport Protocol Framework", Work in Progress, Internet-Draft, draft-ietf- webtrans-overview-14, 2 November 2026, . [ISOIEC14496-12] ISO/IEC, "Information technology -- Coding of audio-visual objects -- Part 12: ISO base media file format", ISO/ IEC 14496-12, n.d.. [ISOIEC23090-12] ISO/IEC, "Information technology -- Coded representation of immersive media -- Part 12: MPEG Immersive video (MIV)", ISO/IEC 23090-12:2025, 2025, . [RFC10034] Ilola, L. and L. Kondrad, "RTP Payload Format for Visual Volumetric Video-Based Coding (V3C)", RFC 10034, DOI 10.17487/RFC10034, August 2026, . [W3C-WEBCODECS] World Wide Web Consortium, "WebCodecs", n.d., . Appendix A. Design Options for Datagram-Mode Encoding This appendix is informative. It does not change Section 5.7.1. It states the design problem, the working choice in this document, and alternatives on which Media Over QUIC Working Group input is requested. A.1. Problem [I-D.ietf-moq-transport-23], Section 11.2, maps one MOQT object with Delivery Mode Datagram to one OBJECT_DATAGRAM. If the object header, object properties, and payload exceed the session maximum datagram size, the object is dropped without notification. Each hop can have a different maximum. Relays can add Object Properties and thereby increase the encoded size. QUIC DATAGRAM frames cannot be fragmented [RFC9221]. WebTransport exposes a smaller application datagram size than the QUIC max_datagram_frame_size because HTTP Datagram framing consumes part of the frame [I-D.ietf-webtrans-http3]. You, et al. Expires 19 May 2027 [Page 57] Internet-Draft V3C over MOQT November 2026 A coded V3C unit is typically one access unit and may contain several NAL units. Atlas NAL units have no codec-imposed maximum size ([RFC10034], Section 5.4.1). Video access units commonly exceed a path MTU. RTP therefore defines Single NAL Unit, Aggregation Packet, and Fragmentation Unit structures ([RFC10034], Section 5.4). MOQT does not provide an equivalent datagram fragment. The mapping question is therefore: when Datagram delivery is used, what is the independently transmissible unit, and who is responsible for keeping that unit within the datagram budget? A.2. Option A: Encoder-Constrained Coded Unit (Working Specification) One MOQT Object remains one coded V3C unit. The encoder is configured so that each slice, NAL unit, and the resulting coded unit fit in one OBJECT_DATAGRAM after packaging. If they do not, the publisher uses subgroup stream delivery for that object. Coded V3C unit (access unit) | | encode to datagram budget v One MOQT Object ---> one QUIC or WebTransport datagram | | otherwise v Subgroup stream Figure 12: Option A: encoder-constrained coded unit Pros: * Relays stay unaware of V3C and NAL syntax. * The object mapping in Section 5 is unchanged for both delivery modes. * No V3C datagram fragment header is defined. Cons: * The encoder must know a transport size that is not available until the MOQT session exists, and that can differ on later hops. * Constraining an entire access unit to a datagram often forces many small slices, which can reduce coding efficiency. You, et al. Expires 19 May 2027 [Page 58] Internet-Draft V3C over MOQT November 2026 * A publisher cannot send a large independently useful unit as a datagram without either re-encoding or switching to a stream. This document currently specifies Option A. A.3. Option B: NAL Unit or Slice as Datagram Object When Delivery Mode is Datagram, each independently packetizable NAL unit or coded slice is one MOQT Object. Object IDs increase in decoding order within the Group. Small NAL units MAY share one object when they fit. Subgroup delivery can keep the coded-unit mapping of Section 5.5. Access unit = NAL 0 + NAL 1 + NAL 2 | v Object i NAL 0 DATAGRAM Object i+1 NAL 1 DATAGRAM Object i+2 NAL 2 DATAGRAM Figure 13: Option B: NAL or slice as datagram object Pros: * Matches RTP Single NAL Unit packetization more closely than Option A ([RFC10034], Section 5.4.2). * Loss of one datagram drops one NAL unit, not necessarily the entire coded unit. Atlas tiles that are already independently useful benefit. * Slice size is an existing encoder control; the packager does not invent a fragment header. Cons: * The datagram object boundary is no longer the coded V3C unit. A subscriber must reassemble an access unit from consecutive objects before some video decoders can consume it. * Publishers would emit one object per NAL unit for datagram tracks, which Section 5.5 currently advises against when the only goal is codec framing. * An access unit that still contains one oversized NAL unit cannot be sent as datagrams without also adopting Option C or D, or re- encoding. You, et al. Expires 19 May 2027 [Page 59] Internet-Draft V3C over MOQT November 2026 A.4. Option C: Application-Level Fragments of One Coded Unit The object mapping stays "one coded V3C unit". The packager splits that unit across several OBJECT_DATAGRAM payloads. Each payload begins with a streaming-format fragment header, for example a fragment index and a fragment count. Fragments are distinct MOQT objects (consecutive Object IDs). Using the same Object ID for several datagrams would require a change to MOQT and is not proposed here. Coded V3C unit (one access unit) | v Object k fragment 0 of N DATAGRAM Object k+1 fragment 1 of N DATAGRAM Object k+2 fragment 2 of N DATAGRAM Figure 14: Option C: application-level fragments Pros: * The encoder need not target a datagram MTU. * Relays still see opaque objects. * Subgroup delivery can carry the same unit unfragmented. Cons: * This document would have to define a fragment header, reassembly, and loss behavior. Loss of any fragment typically makes the coded unit useless, which is weaker than a subgroup stream and similar to IP fragmentation. * Receivers must wait for N datagrams and detect missing fragments without MOQT-level notification. * The same problem exists for LOC samples and CMAF chunks. Defining fragments only in the V3C packaging may be the wrong layer. A.5. Option D: RFC 10034 RTP Payload Format for V3C Object payloads would use the RFC 10034 structures: Single NAL Unit, Aggregation Packet, and Fragmentation Unit. Each RTP-sized payload would be one MOQT Object sent as a datagram. Pros: You, et al. Expires 19 May 2027 [Page 60] Internet-Draft V3C over MOQT November 2026 * Reuses an existing V3C atlas packetizer, including FU without encoder cooperation ([RFC10034], Section 5.4.4). * Aggregation of small NAL units is already specified. Cons: * RTP payload headers, decoding-order numbers, and FU headers would appear inside MOQT objects. Sequencing would mix RTP and MOQT object identities. * Video components would still need the corresponding RTP payload formats, not only RFC 10034. * This option conflicts with the current rule that this document does not define RTP packetization inside MOQT objects. A.6. Option E: Datagrams Only for Units That Already Fit Do not try to place ordinary video or atlas access units in datagrams. Use Delivery Mode Datagram only for units that are already small and independently useful, for example viewport tiles, optional enhancement data, or small atlas NAL units. Use subgroup streams for reconstruction-critical and oversized coded units. Track (mixed delivery modes) Group n Subgroup 0 base geometry AU stream Datagram optional tile / LoD DATAGRAM Figure 15: Option E: datagrams only when the unit already fits Pros: * Requires no new header and no encoder-to-MTU coupling beyond "do not datagram what does not fit". * Matches MOQT's existing drop-if-too-large rule and the permission to mix Subgroup and Datagram in one track ([I-D.ietf-moq-transport-23], Section 2.1). * Reconstruction-critical data keeps reliable ordered delivery. Cons: * Geometry and occupancy access units stay on streams, so this option does not provide datagram latency for those components. You, et al. Expires 19 May 2027 [Page 61] Internet-Draft V3C over MOQT November 2026 * Publishers need a clear policy for which V3C unit types are eligible. That policy could live in this document without new wire formats. Option E can be combined with Option A or B for the units that remain eligible for datagrams. A.7. Orthogonal Questions These questions apply to more than one option. Scope: Is datagram size a V3C packaging issue, a general MSF/LOC issue, or a MOQT issue? LOC samples and other MSF packagings face the same OBJECT_DATAGRAM limit. Budget signaling: Should the encoder learn the budget only from the local session (max_datagram_frame_size or the WebTransport maximum datagram size), or should MSF advertise a conservative object- payload budget in the catalog so encoding can start before SETUP? Path heterogeneity: The original publisher knows only the first hop. Should a relay that cannot forward an OBJECT_DATAGRAM on a smaller downstream session drop it (current MOQT), or must the publisher leave headroom? MOQT version 23 requires an object in a subscription to be sent according to its Delivery Mode, so a relay cannot rewrite Datagram delivery to a subgroup stream. Relay inflation: How much headroom should a publisher reserve for Object Properties added downstream? This document currently leaves that as a publisher choice. Fallback: MOQT already allows mixing Subgroup and Datagram in one track. Is per-object fallback from Datagram to Subgroup when the encoded unit is too large (Option A) sufficient, or must a track declare a single delivery mode? A.8. Requested WG Input to Datagram Design Options The authors request comment on: 1. Whether Option A should remain the V3C mapping for datagrams. 2. Whether Option B should be permitted or required when Datagram delivery is used, including for atlas tiles. 3. Whether Option C belongs in this document, in MSF, or not at all. You, et al. Expires 19 May 2027 [Page 62] Internet-Draft V3C over MOQT November 2026 4. Whether Option D (RTP structures inside MOQT objects) should stay out of scope. 5. Whether Option E should be the recommended operational profile, with datagrams limited to independently discardable units that already fit. 6. Which layer should specify the datagram payload budget and any headroom for relays. Appendix B. Single-Track Encapsulation Mode This appendix specifies single-track mode, in which all V3C components are carried in one MOQT track. This mode reduces the number of subscriptions, but it prevents per-component subscription, prioritization, and independent adaptive bitrate switching, and therefore is NOT RECOMMENDED. A publisher that uses single-track mode MUST follow this appendix. Except as specified in this appendix, the requirements in the body of this document apply. B.1. Track and Catalog Each Object carries one complete V3C composition unit as a sequence of V3C units, each preceded by a length field and each including its four-byte V3C unit header. Because every Object carries all components of one composition unit, subgroups cannot separate component types. The catalog v3c object of the track omits all fields except parameterSetId and framing (Section 7.2). The codec value is v3e1 or v3eg for V-PCC, or vdm1 or vdmg for V-DMC ([ISOIEC23090-10], Clauses 7.4.1 and 7.6.2). With native framing, the codec value is v3eg or vdmg. B.2. Initialization Data The track references with initRef the VPS as specified in Section 5.3: the v3c_parameter_set() with native framing, or a V3CDecoderConfigurationRecord with ISOBMFF framing. A V3C unit of type V3C_VPS MAY also be included in the first Object of a Group so that a stored Group remains self-contained. With ISOBMFF framing, carriage of video decoder configuration for this mode is not specified by this document. You, et al. Expires 19 May 2027 [Page 63] Internet-Draft V3C over MOQT November 2026 B.3. Object Payload With native framing, an Object payload is a V3C sample stream ([ISOIEC23090-5], Annex C): one sample_stream_v3c_header() followed by one sample_stream_v3c_unit() for each V3C unit of the composition unit. Each sample_stream_v3c_unit() contains the complete v3c_unit(), including its V3C unit header. The size of each ssvu_v3c_unit_size field is given by ssvh_unit_size_precision_bytes_minus1 of that Object's header. With ISOBMFF framing, an Object payload is a V3CBitstreamSample ([ISOIEC23090-10], Clause 7.3.1.2). The size of its length fields is given by unit_size_precision_bytes_minus1 in the V3CDecoderConfigurationRecord that the track references with initRef. Acknowledgments The authors thank contributors to the Media Over QUIC Working Group and to the V3C RTP payload format work for discussion of volumetric media carriage. Authors' Addresses Yu You Nokia Email: yu.you@nokia.com Serhan Gül Nokia Email: serhan.guel@nokia.com Lukasz Kondrad Nokia Email: lukasz.kondrad@nokia.com Patrice Rondao Alface Nokia Email: patrice.rondao_alface@nokia.com Lauri Ilola Nokia Email: lauri.ilola@nokia.com You, et al. Expires 19 May 2027 [Page 64]